Panasonic MCCG901 MCCG901 User Guide - Page 44

To Remove Belt, AGITATOR ASSEMBLY

Get Panasonic MCCG901 - CANISTER VACUUM - MULTI LANGUAGE PDF manuals and user guides
UPC - 885170026476
View all Panasonic MCCG901 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

Belt Courroie Correa To Remove Belt ➢ Remove worn belt. ➢ Check and clean end cap areas. See AGITATOR ASSEMBLY for picture of complete agitator assembly. Motor Shaft Arbre du moteur Eje del transmission del motor Belt Guard Protège-courroie Protector de correa To Replace Belt ➢ Install new belt in belt groove on the agitator assembly, then over the motor shaft. Be sure belt is under the belt guard. ➢ Insert both support tabs into the base slots. Then snap end caps into place. Front Support Tab Languette de support à l'avant Pestaña delantera del soporte Cover Slot Fente du couvercle Ranura de la cubierta Front Base Tab Languette à l'avant de la base Pestaña delantera de la base ➢ Line up tabs on front of base with slots inside the front cover. ➢ Tilt cover to back. Press cover firmly until rear tabs snap into place. Rear Base Tab Languette à l'arrière de la base Pestaña posterior de la base ➢ Turn POWER NOZZLE over. Replace the cover screws and lower the pile height adjustment rollers into place. - 44 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
- 44 -
➢
Remove worn belt.
➢
Check and clean end cap areas. See
AGITATOR ASSEMBLY
for picture of
complete agitator assembly.
Front Support Tab
Languette de support à l’avant
Pestaña delantera del soporte
Cover Slot
Fente du couvercle
Ranura de la cubierta
Front Base Tab
Languette à l’avant de la base
Pestaña delantera de la base
Rear Base Tab
Languette à l’arrière de la base
Pestaña posterior de la base
Belt Guard
Protège-courroie
Protector de correa
Motor Shaft
Arbre du moteur
Eje del
transmission
del motor
Belt
Courroie
C
orrea
➢
Install new belt in belt groove on the
agitator assembly, then over the motor
shaft.
Be sure belt is under the belt guard.
➢
Insert both support tabs into the base slots.
Then snap end caps into place.
➢
Line up tabs on front of base with slots
inside the front cover.
➢
Tilt cover to back. Press cover firmly until
rear tabs snap into place.
➢
Turn POWER NOZZLE over.
Replace the
cover screws and lower the pile height
adjustment rollers into place.
To Remove Belt
To Replace Belt