Panasonic SC-ZT2s Operating Instructions - Page 25
Error messages, Using with headphones, Specifications
View all Panasonic SC-ZT2s manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 25 highlights
Error messages Display CANCEL MUTE FUNCTION (Scrolling) MUTE (Blinking) NOT POSSIBLE FOR THIS INPUT SOURCE (Scrolling) NOT POSSIBLE FOR THIS PCM SOURCE (Scrolling) NOT POSSIBLE WHEN USING HEADPHONES (Scrolling) REMOTE 2 REMOTE 1 SWITCH OFF POWER (Scrolling) TURN OFF DTS FIX MODE (Scrolling) U701 U703 U704 Check point/Cause/Countermeasure • The test signal is not output while muting is on. Cancel muting for operation. • This is always displayed while muting is on. • You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic for dual sounds. • You cannot use Dolby Virtual Speaker, SFC and Dolby Pro Logic effect with PCM signals with sampling frequency of over 48 kHz. • You cannot use the sound field effects when using headphones. • Set the same remote control code for this main unit and remote control. When "REMOTE 2 " is displayed, set the code to "2 " on the remote control in step 4 of procedure "When other equipment (mini component system, AV amp, etc.) manufactured by Panasonic operates with the remote control operations of this system". When "REMOTE 1 " is displayed, set the code to "1 " on the remote control in step 4 in the same way. • While "F70 " is displayed, all operations but turning ON/OFF operation are not available. Turn off the system, unplug the AC power supply cord, and consult your dealer. • When each input is fixed to DTS (DTS FIX), the sound field effects cannot be canceled even if you press [-SETUP, OFF]. Cancel DTS FIX. • The equipment connected by the HDMI cable is not compatible with this system's copyright protection technology. • A problem has occurred with the HDMI connection. Try the following to correct the problem. Consult your dealer if the error code remains on the display. - Turn the connected equipment off and on again. - Disconnect the HDMI cable then reconnect it. - Do not connect more than 2 sets of equipment to this system's output. • The system received incompatible video signals through HDMI connection. Check the settings of the connected equipment. Pages 20 20 - 17 25 24 - 24 - - - Error messages/Using with headphones/Specifications Using with headphones Turn down the volume closest to the minimum value. • Plug type: ø 3.5 mm (1/8 in.) stereo mini plug W (Headphone) jack Headphones (not included) Note • Avoid listening for prolonged periods of time to prevent hearing damage. • Multi-channel signals are forcibly converged to 2-channel and output. (2CH MIX) However, for DVD audio, the front left and right signals are output. Specifi cations MAIN UNIT g PRE AMPLIFIER SECTION Input sensitivity / Input impedance TV, AUX3 600 mV / 47 kΩ S/N ratio (IHF A) BD/DVD, TV, AUX1, AUX2 (Digital Input) 80 dB (IHF '66) Tone controls BASS TREBLE Input/Output terminal 50 Hz, + 6 to -6 dB 20 kHz, + 6 to - 6 dB Audio Input Analog Input ( TV, AUX3 ) 2 Optical Digital Input ( TV, AUX2 ) 2 Audio Output Audio Output ( Front L/R, Surround L/R ) 4 Subwoofer Output 1 Headphone Output ( 16 to 64 Ω ) 1 Video/Audio HDMI Input ( BD/DVD, AUX1 ) 2 HDMI Output ( TO TV (ARC)) 1 This system supports "HDAVI Control 4" function. g MAIN UNIT GENERAL Power supply Power consumption AC 120 V, 60 Hz 16 W In standby condition In standby condition ( HDMI off mode ) 0.5 W 0.2 W Dimensions ( W x H x D ) 430 mm x 59 mm x 262 mm (16-15/16" x 2-5/16" x 10-5/16") Mass [ Weight ] Approx. 2 kg (4.4 lb.) Operating temperature range 0°C to 40 °C (32°F to 104 °F) Operating humidity range 20 % to 80 % RH (no condensation) g WIRELESS SECTION Frequency of the using band 2.4000 GHz to 2.4835 GHz Number of using channels 3 The reaching distance 15 m (49 ft)∗1 ∗1 It is under the condition as follows. At same room indoor, there is not an obstacle between the main unit and the speaker. And installing a main unit in the position with equal to or more than 50 cm height. SPEAKER g POWER AMPLIFIER SECTION∗2 RMS output power 10 % total harmonic distortion Woofer Speaker ch 60 W (100 Hz, 3 Ω) Mid High Speaker ch 20 W (1 kHz, 8 Ω) System Total Power∗3 160 W (80 W x 2) FTC output power 1.0 % total harmonic distortion 50 Hz to 250 Hz Woofer Speaker ch 37 W (3 Ω) 250 Hz to 20 kHz Mid High Speaker ch 13 W (8 Ω) System Total Power∗3 100 W (50 W x 2) g SPEAKER SECTION∗2 2-way 5 speakers system (Bass reflex type) Woofer part 12 cm cone type x 1 Mid High part 2.4 x 10 cm flat type x 4 g SPEAKER GENERAL∗2 Power supply Power consumption AC 120 V, 60 Hz 20 W Wireless Link Standby In Standby condition 0.8 W 0.1 W Dimensions ( W x H x D ) 290 mm x 1231 mm x 290 mm (11-13/32" x 48-15/32" x 11-13/32") Mass [ Weight ] Approx. 3.9 kg (8.6 lb.) Operating temperature range 0°C to 40°C (32°F to 104°F) Operating humidity range 20 % to 80 % RH (no condensation) ∗2: per 1 speaker ∗3: use 2 speakers Note: 1. Specifications are subject to change without notice. 2. Total harmonic distortion is measured by the digital spectrum analyzer. 3. Total harmonic distortion is measured by using AES17 filter. 25 VQT2R70 Troubleshooting and other information