Panasonic TD7896W User Guide - Page 36

Problem, Description and Solution, the Incoming Call Log, - troubleshooting

Page 36 highlights

Troubleshooting and Error Messages Problem Description and Solution While Caller ID is displayed using • Caller ID is displayed for about 20 seconds. If you press the Incoming Call Log, the during that time period, the display goes blank until display goes blank after pressing the time expires. . (KX-TA624/824 only) → Press then press to return to the standby display. Some received calls are not stored in the Incoming Call Log. (KX-TA308 only) → Incoming calls via Voice Call/Paging/LCS/Auto Answer cannot be stored in the Incoming Call Log. → Set at least one of the incoming call types to On. (See page 34.) Some dialed calls are not stored in the Outgoing Call Log. → Outgoing calls using some PBX features (e.g., Redial, Onetouch Dialing or Speed Dialing) cannot be stored in the Outgoing Call Log. Even when in standby mode, you • The BGM setting may be on. cannot access the Phonebook or other menus. ( is displayed in standby → KX-TA824: Set program [626] BGM Control for APT to "Disable" in PBX System Programming. → KX-TA308/624: Press "1" to turn BGM off. mode.) Noise is frequently heard. → Set the handset and base unit away from other electrical appliances. → Move closer to the base unit. Two short beeps are heard during a conversation. • The radio signal is weak. → Move closer to the base unit. The charge indicator flashes red • The charger is not connected properly. rapidly. → Make sure the battery is inserted properly. → Set the handset in the charger properly. You charged the battery for 7 • The battery charge contacts may be dirty. hours, but the beep tones sound → Clean the battery charge contacts without damaging them every 5 seconds and (needs and charge once more. to be charged) flashes after a few • It is time to change the battery. telephone calls. → Replace with a new one. The battery indicator does not display the remaining charge properly after you replace the battery. → Charge the battery for about 7 hours when the low battery warning is displayed. While operating the unit, the AC • These are normal conditions. adaptor feels warm. While charging the battery, the handset feels warm. 36

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40

Troubleshooting and Error Messages
36
While Caller ID is displayed using
the Incoming Call Log, the
display goes blank after pressing
. (KX-TA624/824 only)
• Caller ID is displayed for about 20 seconds. If you press
during that time period, the display goes blank until
the time expires.
Press
then press
to return to the standby display.
Some received calls are not
stored in the Incoming Call Log.
(KX-TA308 only)
Incoming calls via Voice Call/Paging/LCS/Auto Answer
cannot be stored in the Incoming Call Log.
Set at least one of the incoming call types to On. (See
page 34.)
Some dialed calls are not stored
in the Outgoing Call Log.
Outgoing calls using some PBX features (e.g., Redial, One-
touch Dialing or Speed Dialing) cannot be stored in the
Outgoing Call Log.
Even when in standby mode, you
cannot access the Phonebook or
other menus.
(
is displayed in standby
mode.)
• The BGM setting may be on.
KX-TA824: Set program [626] BGM Control for APT to
“Disable” in PBX System Programming.
KX-TA308/624: Press “1” to turn BGM off.
Noise is frequently heard.
Set the handset and base unit away from other electrical
appliances.
Move closer to the base unit.
Two short beeps are heard
during a conversation.
• The radio signal is weak.
Move closer to the base unit.
The charge indicator flashes red
rapidly.
• The charger is not connected properly.
Make sure the battery is inserted properly.
Set the handset in the charger properly.
You charged the battery for 7
hours, but the beep tones sound
every 5 seconds and
(needs
to be charged) flashes after a few
telephone calls.
• The battery charge contacts may be dirty.
Clean the battery charge contacts without damaging them
and charge once more.
• It is time to change the battery.
Replace with a new one.
The battery indicator does not
display the remaining charge
properly after you replace the
battery.
Charge the battery for about 7 hours when the low battery
warning is displayed.
While operating the unit, the AC
adaptor feels warm. While
charging the battery, the handset
feels warm.
• These are normal conditions.
Problem
Description and Solution