Pfaff expression 2044 Owner's Manual - Page 66

damaged area

Get Pfaff expression 2044 PDF manuals and user guides View all Pfaff expression 2044 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

.4 - I __..._J Darning with the straight stitch - 1 Attach darning foot No. 6. Turn the handwheel toward you until the needle is set at its highest position. With thumb and index finger press the darning foot together. Insert the pin of the darning foot as far as it will go into the hole of the presser foot holder. The "C-shaped" guide should place itself around the presser bar. The long, plastic arm must be behind the needle clamp/needle set screw. Tighten the set screw. 4+ 1 - -J - -:-'- ArtH • Darning position: Lower the presser bar lifter slowly and push it to the rear until it engages in the darning position. In this position the thread tension is engaged for darning. • Lower the feed dog. • Draw up the bobbin thread and hold the threads when you start sewing. • Repair the damaged area/hole by guiding the fabric evenly forwards and backwards. The length of the seam is determined by the size of the hole. • When you have covered the width of the damaged area, turn the fabric 90 degrees and stitch over the area again. Darning in both directions over a tear will produce a stronger repair. Tip: Remember when sewing with the feed dogs lowered. the stitch length is determined by you. An even, medium-to-fast sewing speed will allow you to sew a more consistent length of straight stitch. Sewing too slowly may cause small knots to appear on the reverse side of your work 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
__..._J
Darning
with
the
straight
stitch
—
1
Attach
darning
foot
No.
6.
Turn
the
handwheel
toward
you
until
the
needle
is
set
at
its
highest
position.
With
thumb
and
index
finger
press
the
darning
foot
together.
Insert
the
pin
of
the
darning
foot
as
far
as
it
will
go
into
the
hole
of
the
presser
foot
holder.
The
“C-shaped”
guide
should
place
itself
around
the
presser
bar.
The
long,
plastic
arm
must
be
behind
the
needle
clamp/needle
set
screw.
Tighten
the
set
screw.
•
Darning
position:
Lower
the
presser
bar
lifter
slowly
and
push
it
to
the
rear
until
it
engages
in
the
darning
position.
In
this
position
the
thread
tension
is
engaged
for
darning.
•
Lower
the
feed
dog.
•
Draw
up
the
bobbin
thread
and
hold
the
threads
when
you
start
sewing.
.4
-
I
•
Repair
the
damaged
area/hole
by
guiding
the
fabric
evenly
forwards
and
backwards.
The
length
of
the
seam
is
determined
by
the
size
of
the
hole.
•
When
you
have
covered
the
width
of
the
damaged area,
turn
the
fabric
90
degrees
and
stitch
over
the
area
again.
Darning
in
both
directions
over
a
tear
will
produce
a
stronger
repair.
Tip:
Remember
when
sewing
with
the
feed
dogs
lowered.
the
stitch
length
is
determined
by
you.
An
even,
medium-to-fast
sewing
speed
will
allow
you
to
sew
a
more
consistent
length
of
straight
stitch.
Sewing
too
slowly
may
cause
small
knots
to
appear
on
the
reverse
side
of
your
work
63
4+
1
—
-J
-
-:-‘-
ArtH