Pioneer AVIC-D2 Owner's Manual - Page 121

Appendix, NAVI/AV, Areas to Avoid, Avoid Ferry - bypass

Get Pioneer AVIC-D2 PDF manuals and user guides View all Pioneer AVIC-D2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 121 highlights

NAVI/AV Appendix Message No XM signal. Please wait. XM updating. Please wait. UPDATING Route calculation was not possible. Route calculation was not possible because the destination is too far. Route calculation was not possible because the destination is too near. Route calculation was not possible due to traffic regulations. Route calculation was not possible because no guidance can be provided around the destination or the starting point. There is no route to the destination. The route could not avoid the specified area. The route could not avoid the specified area. Toll road has not been avoided. Ferry has not been avoided. When While waiting for a response from the XM tuner. You are in an area that cannot receive XM tuner reception. Your current location provides very poor reception. Service subscription is either XM audio only or XM NavTraffic stand alone. Radio is being updated with the latest encryption code. The selected channel is not included in your subscription. Radio is being updated with the latest encryption code. Route calculation has failed because of malfunction of map data, software, hardware, or disc. The destination is too far. The destination or way point(s) is too close. • The destination or way point(s) are in a Control Traffic Zone (CTR) and the route calculation is hampered. • Your vehicle is currently in a Control Traffic Zone (CTR) and the route calculation is hampered. The destination, way point(s), or starting point are in an area where no road exists (e.g. a mountain) and the route calculation is impossible. The destination or way point(s) are in an isolated island, etc. without a ferry and the route calculation is impossible. If route setting cannot avoid specified Areas to Avoid. If the route to the destination (or way point) cannot be established by bypassing toll roads (including toll areas) and Areas to Avoid. In case a ferry route was included in the route to the destination or way points even though "Avoid Ferry" was set to ON. What to do Wait for a while and try the operation again. Move into an area that can receive XM tuner reception. Change your location. Since the GEX-P10XMT is capable of receiving both XM audio and XM NavTraffic service, if you are subscribed to only one or the other, the system checks to see if you have added another service to your account since you last powered on the navigation system. When you subscribe to both services, this message will stop appearing when you turn the ignition ON (ACC ON). Wait until the encryption code is fully updated. Select another channel. Wait until the encryption code is fully updated. • Change the destination. • Clean the disc. • Consult the Pioneer Local dealer if this message persists. • Set a destination closer to the start- ing point. • Set one or more way points. Set a destination [and way point(s)] farther from the starting point. • Set a destination and way point(s) outside the CTR if you know where the restricted area is. • Try the destination or way point(s) away from the currently set points to some extent. • Drive your vehicle to an unrestricted area and reset the destination and way point(s). • Set a destination and way point(s) on roads. • Reset the destination after you drive the vehicle to any road. Change the destination. If the current route is not desired, set destination or way points that do not pass through the Areas to Avoid. If the current route is not desired, set destination or way points that do not pass through toll roads (including toll areas) and Areas to Avoid. If the current route is not desired, set destination or way points that do not pass through a ferry route. 119

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
119
Appendix
NAVI/AV
No XM signal. Please wait.
While waiting for a response from
the XM tuner.
Wait for a while and try the operation
again.
You are in an area that cannot
receive XM tuner reception.
Move into an area that can receive
XM tuner reception.
Your current location provides very
poor reception.
Change your location.
XM updating. Please wait.
Service subscription is either
XM audio only
or XM NavTraffic
stand alone
.
Since the GEX-P10XMT is capable of
receiving both XM audio and XM
NavTraffic service, if you are sub-
scribed to only one or the other, the
system checks to see if you have
added another service to your
account since you last powered on
the navigation system. When you
subscribe to both services, this mes-
sage will stop appearing when you
turn the ignition ON (ACC ON).
Radio is being updated with the lat-
est encryption code.
Wait until the encryption code is fully
updated.
UPDATING
The selected channel is not included
in your subscription.
Select another channel.
Radio is being updated with the lat-
est encryption code.
Wait until the encryption code is fully
updated.
Route calculation was not possible.
Route calculation has failed because
of malfunction of map data, software,
hardware, or disc.
• Change the destination.
• Clean the disc.
• Consult the Pioneer Local dealer if
this message persists.
Route calculation was not possible
because the destination is too far.
The destination is too far.
• Set a destination closer to the start-
ing point.
• Set one or more way points.
Route calculation was not possible
because the destination is too near.
The destination or way point(s) is too
close.
Set a destination [and way point(s)]
farther from the starting point.
Route calculation was not possible
due to traffic regulations.
• The destination or way point(s) are
in a Control Traffic Zone (CTR) and
the route calculation is hampered.
• Your vehicle is currently in a Con-
trol Traffic Zone (CTR) and the
route calculation is hampered.
• Set a destination and way point(s)
outside the CTR if you know where
the restricted area is.
• Try the destination or way point(s)
away from the currently set points
to some extent.
• Drive your vehicle to an unre-
stricted area and reset the destina-
tion and way point(s).
Route calculation was not possible
because no guidance can be pro-
vided around the destination or the
starting point.
The destination, way point(s), or
starting point are in an area where no
road exists (e.g. a mountain) and the
route calculation is impossible.
• Set a destination and way point(s)
on roads.
• Reset the destination after you
drive the vehicle to any road.
There is no route to the destination.
The destination or way point(s) are in
an isolated island, etc. without a ferry
and the route calculation is impossi-
ble.
Change the destination.
The route could not avoid the speci-
fied area.
If route setting cannot avoid speci-
fied
Areas to Avoid
.
If the current route is not desired, set
destination or way points that do not
pass through the
Areas to Avoid
.
The route could not avoid the speci-
fied area.
Toll road has not been avoided.
If the route to the destination (or way
point) cannot be established by
bypassing toll roads (including toll
areas) and
Areas to Avoid
.
If the current route is not desired, set
destination or way points that do not
pass through toll roads (including
toll areas) and
Areas to Avoid
.
Ferry has not been avoided.
In case a ferry route was included in
the route to the destination or way
points even though “
Avoid Ferry
”
was set to
ON
.
If the current route is not desired, set
destination or way points that do not
pass through a ferry route.
Message
When
What to do