Pioneer DEH-6300UB Owner's Manual - Page 10
Audio Adjustments, Initial Settings, Operating this unit - subwoofer
UPC - 884938121163
View all Pioneer DEH-6300UB manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
Section 02 Operating this unit Operating this unit Function settings 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select FUNCTION. 3 Turn M.C. to select the function. After selecting, perform the following procedures to set the function. BOOK MARK (bookmark) 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. For details, refer to Storing song information (Bookmark) on the previous page. 3 Press M.C. to confirm the selection. PAUSE (pause) 1 Press M.C. to pause or resume. S.RTRV (sound retriever) 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. For details, refer to Enhancing compressed audio and restoring rich sound (sound retriever) on the previous page. 3 Press M.C. to confirm the selection. Audio Adjustments 1 Press M.C. to display the main menu. 2 Turn M.C. to change the menu option and press to select AUDIO. 3 Turn M.C. to select the audio function. After selecting, perform the following procedures to set the audio function. 10 En FAD/BAL (fader/balance adjustment) 1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between fader (front/rear) and balance (left/right). 3 Turn M.C. to adjust the speaker balance. ! When the rear output and RCA output setting are SW, you cannot adjust front/rear speaker balance. Refer to SW CONTROL (rear output and subwoofer setting) on the next page. PRESET EQ (equalizer recall) 1 Press M.C. to display the setting mode. 2 Turn M.C. to select an equalizer curve. POWERFUL-NATURAL-VOCAL-CUSTOM1-CUSTOM2-FLAT-SUPER BASS 3 Press M.C. to confirm the selection. GRAPHIC EQ (equalizer adjustment) You can adjust the currently selected equalizer curve setting as desired. Adjusted equalizer curve settings are stored in CUSTOM1 or CUSTOM2. ! A separate CUSTOM1 curve can be created for each source. If you make adjustments when a curve other than CUSTOM2 is selected, the equalizer curve settings will be stored in CUSTOM1. ! A CUSTOM2 curve that is common for all sources can be created. If you make adjustments when the CUSTOM2 curve is selected, the CUSTOM2 curve will be updated. 1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between equalizer band and level. 3 Press M.C. to switch to equalizer band and then turn M.C. to select. 100HZ-315HZ-1.25KHZ-3.15KHZ-8KHZ 4 Press M.C. to switch to level and then turn M. C. to adjust. Adjustment range: +6 to -6 LEVEL METER (level meter display setting) 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. OFF (off)-MODE1-MODE2-MODE3- MODE4 3 Press M.C. to confirm the selection. LOUDNESS (loudness) Loudness compensates for deficiencies in the lowand high-frequency ranges at low volume. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. OFF (off)-LOW (low)-MID (mid)-HIGH (high) 3 Press M.C. to confirm the selection. SW SETTING 1 (subwoofer on/off setting) This unit is equipped with a subwoofer output which can be turned on or off. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the desired setting. NORMAL (normal phase)-REVERSE (reverse phase)-OFF (subwoofer off) 3 Press M.C. to confirm the selection. SW SETTING 2 (subwoofer adjustment) The cut-off frequency and output level can be adjusted when the subwoofer output is on. Only frequencies lower than those in the selected range are outputted from the subwoofer. 1 Press M.C. to display the setting mode. 2 Press M.C. to cycle between the cut-off fre- quency and output level of the subwoofer. 3 Press M.C. to switch to cut-off frequency and then turn M.C. to select the cut-off frequency. 50HZ-63HZ-80HZ-100HZ-125HZ 4 Press M.C. to switch to output level and then turn M.C. to adjust the output level. Adjustment range: +6 to -24 HPF SETTING (high pass filter adjustment) When you do not want low sounds from the subwoofer output frequency range to play from the front or rear speakers, turn on the HPF (high pass filter). Only frequencies higher than those in the selected range are output from the front or rear speakers. 1 Press M.C. to display the setting mode. 2 Turn M.C. to select the cut-off frequency. OFF (off)-50HZ-63HZ-80HZ-100HZ- 125HZ 3 Press M.C. to confirm the selection. BASS BOOSTER (bass boost) 1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the level. Adjustment range: 0 to +6 3 Press M.C. to confirm the selection. SLA (source level adjustment) SLA (Source Level Adjustment) lets you adjust the volume level of each source to prevent radical changes in volume when switching between sources. ! When selecting FM as the source, you cannot switch to SLA. ! Settings are based on the FM volume level, which remains unchanged. ! The AM volume level can also be adjusted with this function. 1 Press M.C. to display the setting mode. 2 Turn M.C. to adjust the source volume. Adjustment range: +4 to -4 3 Press M.C. to confirm the selection. Initial Settings 1 Press and hold SRC/OFF until the unit turns off. 2 Press M.C. and hold until the initial setting menu appears in the display.