Pioneer DJM-800 Owner's Manual - Page 5
Connections - used
UPC - 012562796604
View all Pioneer DJM-800 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 5 highlights
CONNECTIONS CONNECTION PANEL 1 2 3 CONNECTIONS (CONNECTION PANEL) 4 5 6 7 8 AC IN POWER OFF ON MASTER 2 REC L 1GND R 2HOT 3COLD SIGNAL GND PHONO LINE L PHONO LINE L SIGNAL GND PHONO CD L LINE CD L CONTROL CONTROL CONTROL CONTROL R R DIGITAL LINE MASTER ATT -3dB0dB -6dB -12dB DIGITAL LINE R DIGITAL CD R DIGITAL CD DIGITAL IN DIGITAL OUT fs (Hz) 48 k 96 k MIDI OUT R MASTER 1 L ADD CUT MIC SIGNAL R BOOTH L (TRS) R SEND L(MONO) R RETURN L(MONO) 21 20 19 18 17 16 15 14 13 12 11 10 9 1. POWER switch 2. MASTER 2 output connectors RCA type unbalanced output. 3. Recording output connectors (REC) RCA type output connectors for recording. 4. PHONO input connectors RCA type phono level (MM cartridge) input connectors. Do not use for inputting line level signals. 5. LINE input connectors RCA type line level input connectors. Use to connect a cassette deck or other line level output component. 6. Signal grounding terminals (SIGNAL GND) Use to connect ground wires from analog players. This is not a safety grounding terminal. 7. CD input connectors RCA type line level input connectors. Use to connect a DJ CD player or other line level output component. 8. DIGITAL IN connectors RCA type digital coaxial input connectors. Use to connect to DJ CD player or other digital coaxial output connectors. ÷ The sound may be temporarily interrupted when the output signal's sampling frequency is changed. 9. MIDI OUT connector DIN type output connector. Use to connect to other MIDI component (see P. 20). 10. DIGITAL OUT connector RCA type digital coaxial output connector. Master audio digital output. 11. Sampling frequency selector switch (fs 48 k/96 k) Use to set the sampling frequency of the digital output to 96 kHz/24bit format or 48 kHz/24-bit format. ÷ Turn power off before changing this switch position. 12. DIGITAL/CD input selector switches Use to select either analog input (CD) or digital input (DIGITAL IN). 13. RETURN connectors Ø6.3 mm phone-type input connectors. Use to connect to the output connectors of external effectors or similar components. When the L channel only is connected, the L channel input is simultaneously input to the R channel. 14. SEND output connectors Ø6.3 mm phone-type output connectors. Use to connect to the input connectors of external effectors or other similar components. When the L channel only is connected, a L+R monaural signal is output. 15. CONTROL connectors Ø3.5 mm mini-connector. Use to connect to the control connector of a Pioneer DJ CD player. When the connectors are connected, the DJM-800's fader can be used to perform start/stop on the DJ CD player. 16. BOOTH monitor output connectors Ø6.3 mm phone-type booth monitor output connectors. The sound level from these connectors is controlled independently by the BOOTH MONITOR level dial, regardless of the position of the MASTER LEVEL dial. (These connectors are TRS output, so they support both balanced and unbalanced outputs.) 17. DIGITAL/LINE input selector switches Use to select either analog input (LINE) or digital input (DIGITAL IN). 18. Master output attenuator switch (MASTER ATT) Use to attenuate the level of the master 1 and master 2 outputs. Selectable values are 0 dB, -3 dB, -6 dB and -12 dB. 19. Microphone signal switch (MIC SIGNAL ADD/CUT) When set to the [ADD] position, the sounds from microphone 1 and microphone 2 are output to the BOOTH monitor output connectors. When set to the [CUT] position, the sounds from microphone 1 and microphone 2 are not output to the BOOTH monitor output connectors. 20. MASTER 1 output connectors XLR type (male) balanced output. ÷ When using a cord with RCA-type plug, users are recommended to connect the plug directly to the MASTER 2 connectors without using an XLR/RCA converter plug. 21. Power inlet (AC IN) Use the accessory power cord to connect to an AC power outlet of the proper voltage. 5