Pioneer DV-434 Owner's Manual - Page 54

kHz PCM Out]

Get Pioneer DV-434 PDF manuals and user guides View all Pioneer DV-434 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Remote control operation is not possible. The rear panel control input jack on the player is being used. \ Point the remote control at the component that the player is connected to (page 16). The remote control is too far from the player, or the angle with the remote sensor is too wide. \ Be sure to operate the remote from a location within its operating range (page 8). The batteries are exhausted. \ Replace the exhausted batteries with all new batteries (page 8). No sound from the DIGITAL OUT (optical or coaxial) jacks. The [Digital Out] menu is set to [Off]. \ Set the [Digital Out] (Audio 1 menu) to [On] (page 27). Audio is not output or is distorted. The Setup screen Audio 1 menu [96 kHz PCM Out] setting is set to [96 kHz]. Digital output is prohibited on some discs. \ Be sure to make analog audio connections as well as digital connections (page 15). The disc is dirty. \ Refer to "Disc Care" (page 50). The connection plugs are not inserted fully into the terminals or are not connected. \ Check that all connection plugs are firmly inserted. The connection plug or terminal is dirty. \ Check that the plugs and terminals are wiped clean of dirt, etc. Audio cable connection is wrong. \ Check to make sure that the audio cables are connected correctly (page 15). Connection is made to the stereo amplifier's PHONO input terminal. \ Change connection to any input terminal except PHONO. The pause mode is engaged. \ Press PLAY 3 or PAUSE 8 to exit the pause mode. Stereo amplifier operation is incorrect. \ Check input (CD, AUX, etc.) selector to determine if it is selected for DVD playback. The DVD or CD is recorded in DTS audio. \ DTS audio is only output from the digital output jacks. Connect the digital output on the player to the digital input on a receiver or amplifier with a built in DTS decoder to hear DTS audio. Noticeable difference in DVD and CD volume. DVDs and CDs use different recording methods. \ This is not a malfunction. Caution Static electricity or other external influence may cause malfunctioning of this unit. In this case, unplugging the power cord and then re-plugging it in will usually reset the unit for proper operation. If this does not correct the problem, please consult your nearest 54 PIONEER service center.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
54
Remote control operation is not possible.
The rear panel control input jack on the player is being
used.
\
Point the remote control at the component that
the player is connected to (
page 16
).
The remote control is too far from the player, or the
angle with the remote sensor is too wide.
\
Be sure to operate the remote from a location
within its operating range (
page 8
).
The batteries are exhausted.
\
Replace the exhausted batteries with all new
batteries (
page 8
).
No sound from the DIGITAL OUT (optical or coaxial)
jacks.
The
[Digital Out]
menu is set to
[Off]
.
\
Set the
[Digital Out]
(
Audio 1
menu) to
[On]
(
page 27
).
Audio is not output or is distorted.
The Setup screen
Audio 1
menu
[96 kHz PCM Out]
setting is set to
[96 kHz]
. Digital output is prohibited
on some discs.
\
Be sure to make analog audio connections as well
as digital connections (
page 15
).
The disc is dirty.
\
Refer to
“Disc Care”
(
page 50
).
The connection plugs are not inserted fully into the
terminals or are not connected.
\
Check that all connection plugs are firmly inserted.
The connection plug or terminal is dirty.
\
Check that the plugs and terminals are wiped
clean of dirt, etc.
Audio cable connection is wrong.
\
Check to make sure that the audio cables are
connected correctly (
page 15
).
Connection is made to the stereo amplifier‘s PHONO
input terminal.
\
Change connection to any input terminal except
PHONO.
The pause mode is engaged.
\
Press
PLAY
3
or
PAUSE
8
to exit the pause
mode.
Stereo amplifier operation is incorrect.
\
Check input (CD, AUX, etc.) selector to determine
if it is selected for DVD playback.
The DVD or CD is recorded in DTS audio.
\
DTS audio is only output from the digital output
jacks. Connect the digital output on the player to
the digital input on a receiver or amplifier with a
built in DTS decoder to hear DTS audio.
Noticeable difference in DVD and CD volume.
DVDs and CDs use different recording methods.
\
This is not a malfunction.
Caution
Static electricity or other external influence may cause
malfunctioning of this unit. In this case, unplugging
the power cord and then re-plugging it in will usually
reset the unit for proper operation. If this does not
correct the problem, please consult your nearest
PIONEER service center.