Pioneer VSX 1017TXV Owner's Manual - Page 54

09 Other Settings 1 Select 'Dual Mono Setup' from the Other Setup menu. 6.Other Setup a.DRC Setup b.Dual Mono Setup c.LFE ATT Setup d.SR+ Setup e.Video Conv. Setup 6b.Dual Mono Setup Dual Mono [ CH1 :Return :Finish 2 Choose the setting that you want. • CH1 - Only channel 1 is played • CH2 - Only channel 2 is played • CH1 CH2 - Both channels are played through the front speakers 3 When you're finished, press RETURN. You return to the Other Setup menu. LFE Attenuator Setup • Default setting: ATT 0dB Some Dolby Digital and DTS audio sources include ultralow bass tones. Set the LFE attenuator as necessary to prevent the ultra-low bass tones from distorting the sound from the speakers. 1 Select 'LFE ATT Setup' from the Other Setup menu. 6.Other Setup a.DRC Setup b.Dual Mono Setup c.LFE ATT Setup d.SR+ Setup e.Video Conv. Setup 6c. LFE ATT Setup LFE ATT ATT 0dB :Return :Finish 2 Choose the setting that you want. • ATT 0dB - No limiting (recommended) • ATT 10dB - 10 dB of limiting • LFE OFF - No sound from LFE channel 3 When you're finished, press RETURN. You return to the Other Setup menu. SR+ Setup for Pioneer plasma displays • Default setting: OFF (all settings) Make the following settings if you have connected a Pioneer plasma display to this receiver using an SR+ cable. Note that the number of settings available will depend on the plasma display you've connected. See also Using this receiver with a Pioneer plasma display on page 50. 1 Select 'SR+ Setup' from the Other Setup menu. 54 En 6.Other Setup a.DRC Setup b.Dual Mono Setup c.LFE ATT Setup d.SR+ Setup e.Video Conv. Setup :Return 6d.SR+ Setup PDP Volume Control OFF PDP Input Select DVD/LD [ OFF ] TV/SAT [ OFF ] DVR 1 [ OFF ] DVR 2 [ OFF ] VIDEO [ OFF ] Monitor Out [ OFF ] :Finish 2 Select the 'PDP Volume Control' setting you want. • OFF - The receiver does not control the volume of the plasma display • ON - When the receiver is switched to one of the inputs that use the plasma display (DVD/LD, or another function below), the volume on the plasma display is muted so only sound from the receiver is heard. 3 Assign any input source connected to the plasma display to the corresponding input number. This matches the receiver's input source with a numbered video input on the plasma display. For example, assign DVD/LD to input-2 if you have connected your DVD video output to video input 2 on the plasma display. • The Monitor Out should be set to the input that you've used to connect this receiver to your plasma display. 6d.SR+ Setup PDP Volume Control [ ON ] PDP Input Select DVD/LD OFF TV/SAT DVR 1 [ OFF ] [ OFF ] DVR 2 VIDEO [ OFF ] [ OFF ] Monitor Out [ OFF ] :Finish 6d.SR+ Setup PDP Volume Control [ ON ] PDP Input Select DVD/LD input-2 TV/SAT DVR 1 [ OFF ] [ OFF ] DVR 2 VIDEO Monitor Out [ OFF ] [ OFF ] [ OFF ] :Finish 4 When you're finished, press RETURN. You return to the Other Setup menu. Video Converter Setup • Default setting: ON The video converter allows you to see analog video sources through all of this receiver's MONITOR VIDEO OUT jacks. Note that the converter gives priority to component, S-video, then composite (in that order). See About the video converter on page 12 for more on this. 1 Select 'Video Conv. Setup' from the Other Setup menu. 6.Other Setup a.DRC Setup b.Dual Mono Setup c.LFE ATT Setup d.SR+ Setup e.Video Conv. Setup 6e. Video Converter Setup Video Conv. ON :Return :Finish 2 Choose the setting that you want. • ON - All analog video signals are output from the MONITOR VIDEO OUT jacks. • OFF - No conversion between video formats. 3 When you're finished, press RETURN. You return to the Other Setup menu.