Pioneer VSX-21TXH Owner's Manual - Page 71
Using the sleep timer, Dimming the display, Switching the HDMI output, Checking your system settings
UPC - 012562957067
View all Pioneer VSX-21TXH manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 71 highlights
Using other functions 08 Using the sleep timer The sleep timer switches the receiver into standby after a specified amount of time so you can fall asleep without worrying about the receiver being left on all night. Use the remote control to set the sleep timer. INPUT SELECT 12 HDMI OUT 3 SIGNAL SEL MCACC 45 SLEEP 6 SBch A.ATT DIMMER 789 D.ACCESS CH LEVEL 0 CLASS ENTER AUDIO INFO CH DISP TV CTRL RECEIVER REMOTE SETUP ZONE 2 ZONE 3 MAIN • Press RECEIVER , then press SLEEP repeatedly to set the sleep time. 30 min 60 min Off 90 min • You can check the remaining sleep time at any time by pressing SLEEP once. Pressing repeatedly will cycle through the sleep options again.1 Dimming the display You can choose between four brightness levels for the front panel display. Note that when selecting sources, the display automatically brightens for a few seconds. INPUT SELECT 12 HDMI OUT 3 SIGNAL SEL MCACC 45 SLEEP 6 SBch A.ATT DIMMER 789 D.ACCESS CH LEVEL 0 CLASS ENTER AUDIO INFO CH DISP TV CTRL RECEIVER REMOTE SETUP ZONE 2 ZONE 3 MAIN • Press RECEIVER , then press DIMMER repeatedly to change the brightness of the front panel display. Switching the HDMI output (VSX-23TXH only) Set which terminal to use when outputting video and audio signals from the HDMI output terminals (HDMI OUT ALL, HDMI OUT 1 or HDMI OUT 2). The HDMI OUT1 terminal is compatible with the KURO LINK function. INPUT SELECT 12 HDMI OUT 3 SIGNAL SEL MCACC 45 SLEEP 6 SBch A.ATT DIMMER 789 D.ACCESS CH LEVEL 0 CLASS ENTER AUDIO INFO CH DISP TV CTRL RECEIVER REMOTE SETUP ZONE 2 ZONE 3 MAIN • Press RECEIVER , then press HDMI OUT. Please wait a while when Please wait ... is displayed. The output switches among HDMI OUT ALL, HDMI OUT 1 and HDMI OUT 2 each time the button is pressed.2 Checking your system settings Use the status display screen to check your current settings for features such as surround back channel processing and your current MCACC preset. THX PHASE CTRL STATUS ANT MPX PQLS MEMORY AUDIO INFO CH DISP TV CTRL RECEIVER REMOTE SETUP 1 Press RECEIVER , then press STATUS to check the system settings. These appear on the front panel display.3 The front panel display shows each of the following settings for three seconds each: Input Source ↓ Sampling Frequency ↓ Surround Back channel Processing ↓ MCACC preset ↓ ZONE 2 input ↓ ZONE 3 input (VSX-23TXH only) ↓ KURO LINK ↓ HDMI OUT (VSX-23TXH only) 2 When you're finished, press STATUS again to switch off the display. Note 1 • You can also switch off the sleep timer simply by switching off the receiver. • The sleep timer is valid for all zones. If any zone is on, the sleep timer continues functioning. 2 • Synchronized amp mode on page 65 is canceled when the HDMI output is switched. If you wish to use the synchronized amp mode, switch to HDMI OUT 1, then select the synchronized amp mode on the flat panel TV using the flat panel TV's remote control. • When the power is turned off then back on after switching the HDMI output, the input is set to a setting between HDMI1 and HDMI3 (VSX- 21TXH)/4 (VSX-23TXH), or BD. 3 If the Pure Direct mode is switched on, some settings above will show OFF, even though they are on. 71 En