Pioneer VSX-30 Owner's Manual - Page 92
STAND.WAVE Multi-P
UPC - 884938109246
View all Pioneer VSX-30 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 92 highlights
10 The Advanced MCACC menu After a single calibration is performed, each of the following three correction curves can be stored separately in the MCACC memory. SYMMETRY implements symmetric correction for each pair of left and right speakers to flatten the frequency-amplitude characteristics. ALL CH ADJ is a 'flat' setting where all the speakers are set individually so no special weighting is given to any one channel. FRONT ALIGN1 sets all speakers in accordance with the front speaker settings (no equalization is applied to the front left and right channels). • THX Speaker (only available when the Auto MCACC Menu above is ALL or Speaker Setting) - Select YES if you are using THX speakers (set all speakers to SMALL), otherwise leave it set to NO. • STAND.WAVE Multi-P (only available when the Auto MCACC Menu above is EQ Pro & S-Wave) - In addition to measurements at the listening position, you can use two more reference points for which test tones will be analyzed for standing waves. This is useful if you want to get a balanced 'flat' calibration for several seating positions in your listening area.2 Place the microphone at the reference point indicated on-screen and note that the last microphone placement will be at your main listening position: 2nd reference point 1 3rd reference point 2 3 Main listening position 3 Connect the microphone to the MCACC SETUP MIC jack on the front panel. Make sure there are no obstacles between the speakers and the microphone. CONTROL ON / OFF MASTER VOLUME MCACC SETUP MIC iPod iPhone USB VIDEO CAMERA HDMI 5 VSX-31 Microphone Tripod If you have a tripod, use it to place the microphone so that it's about ear level at your normal listening position. If you do not have a tripod, use some other object to install the microphone.3 4 When you're finished setting the options, select START then press ENTER. 5 Follow the instructions on-screen. • Make sure the microphone is connected. • If you're using a subwoofer, it is automatically detected every time you switch on the system. Make sure it is on and the volume is turned up. • See Problems when using the Auto MCACC Setup on page 44 for notes regarding high background noise levels and other possible interference. Note 1 If you selected ALL or Keep SP System as your Auto MCACC menu, you can specify the MCACC preset where you want to save the SYMMETRY, ALL CH ADJ and FRONT ALIGN settings. 2 Switch the Multi-P setting NO if you only use one listening position. 3 Install the microphone on a stable floor. Placing the microphone on any of the following surfaces may make accurate measurement impossible: • Sofas or other soft surfaces. • High places such as tabletops and sofa tops. 92 En
-
1
-
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136