Pioneer VSX-D811S Owner's Manual - Page 69

Additional information

Get Pioneer VSX-D811S PDF manuals and user guides View all Pioneer VSX-D811S manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

Additional information 10 Problem No sound from surround or center speakers. Remedy • Refer to Speaker setting on page 39 to check the speaker settings. • Refer to Setting the relative volume level of each channel on page 44 to check the speaker levels. • Connect the speakers properly (refer to page 19-21). No sound from surround back speakers. • Refer to Surround back speaker setting on page 40 to check the surround back speaker settings. • Refer to the table on page 33 to make sure the 6.1 channel setting and the sound mode are set for surround back sound. Noise during playback of a cassette deck. • Move the cassette deck further from your receiver, until the noise disappears. Sound is produced from other components, but not from LD or DVD player. • Set the SIGNAL SELECT to AUTO, DIGITAL or ANALOG according to the type of connections made. (refer to page 34). • Set the digital input settings correctly (refer to page 43). • Make digital connections (refer to page 14) and set the SIGNAL SELECT to DIGITAL (refer to page 34). • Refer to the instruction manual supplied with the DVD player. No sound is output or a noise is • Set the digital volume level of the player to full, or to the output when software with DTS neutral position. is played back. When a search is performed by • This is not a malfunction, but be sure to turn the volume a DTS compatible CD player down to prevent the output of loud noise from your speakers. during playback, noise is output. Can't operate the remote control. • Replace the batteries (refer to page 6). • Operate within 23 feet ( 7 m), 30° of the remote sensor on the front panel (refer to page 6). • Remove the obstacle or operate from another position. • Avoid exposing the remote sensor on the front panel to direct light. The display is dark or off. • Press FL DIMMER on the remote control repeatedly to return to the default. If the unit does not operate normally due to external effects such as static electricity disconnect the power plug from the outlet and insert again to return to normal operating conditions. XRB3013A.68.74 69 69 En 01.12.12, 5:13 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
Additional information
10
69
En
If the unit does not operate normally due to external effects such as static electricity disconnect the
power plug from the outlet and insert again to return to normal operating conditions.
Problem
No sound from surround or
center speakers.
No sound from surround back
speakers.
Noise during playback of a
cassette deck.
Sound is produced from other
components, but not from LD or
DVD player.
No sound is output or a noise is
output when software with DTS
is played back.
When a search is performed by
a DTS compatible CD player
during playback, noise is output.
Can
’
t operate the remote
control.
The display is dark or off.
Remedy
•
Refer to
Speaker setting
on page 39 to check the speaker
settings.
•
Refer to
Setting the relative volume level of each channel
on
page 44 to check the speaker levels.
•
Connect the speakers properly (refer to page 19
–
21).
•
Refer to
Surround back speaker setting
on page 40 to check
the surround back speaker settings.
•
Refer to the table on page 33 to make sure the 6.1 channel
setting and the sound mode are set for surround back sound.
•
Move the cassette deck further from your receiver, until the
noise disappears.
•
Set the
SIGNAL SELECT
to
AUTO
,
DIGITAL
or
ANALOG
according to the type of connections made. (refer to page 34).
•
Set the digital input settings correctly (refer to page 43).
•
Make digital connections (refer to page 14) and set the
SIGNAL SELECT
to
DIGITAL
(refer to page 34).
•
Refer to the instruction manual supplied with the DVD player.
•
Set the digital volume level of the player to full, or to the
neutral position.
•
This is not a malfunction, but be sure to turn the volume
down to prevent the output of loud noise from your speakers.
•
Replace the batteries (refer to page 6).
•
Operate within 23 feet ( 7 m), 30
°
of the remote sensor on the
front panel (refer to page 6).
•
Remove the obstacle or operate from another position.
•
Avoid exposing the remote sensor on the front panel to direct
light.
•
Press
FL DIMMER
on the remote control repeatedly to return
to the default.
XRB3013A.68.74
01.12.12, 5:13 PM
69