Poulan PRCS16i Owner Manual - Page 13

To limb a tree, To buck a log, To change the power mode, CAUTION, Standard mode

Get Poulan PRCS16i PDF manuals and user guides View all Poulan PRCS16i manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

6. When the tree starts to fall, remove the product from the cut. Stop the motor, put the product down and use the planned escape path. Be careful of limbs falling from above and monitor your footing. • If the log has support on one end, cut 1/3 the diameter from below the log (known as underbucking). • If the log has support on the two ends, cut 1/3 the diameter from the top. Complete the cut by underbucking the lower 2/3 of the log to touch the first cut. To limb a tree 1. Use larger limbs to hold the log off the ground. 2. Remove small limbs in one cut. • If you buck a log on a slope, always stay on the uphill side of the log. Cut through the log while you keep complete control of the product. Then release the cutting pressure near the end of the cut while tightly holding the rear handle and front handle. 3. Cut branches that have tension from the bottom to the top to prevent pinching the saw chain or the guide bar. To buck a log CAUTION: Do not let the saw chain touch the ground. • If the log has support along its full length, cut from the top of the log (known as overbucking). To change the power mode The power mode of the product can be changed while the product is in operation. There are 2 power modes: 1. Standard mode - Saves energy and maximizes run time. Standard mode is applicable for most tasks. Note: The product is set to Standard mode when started. 319 - 002 - 17.11.2017 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
6.
When the tree starts to fall, remove the product from
the cut. Stop the motor, put the product down and
use the planned escape path. Be careful of limbs
falling from above and monitor your footing.
To limb a tree
1.
Use larger limbs to hold the log off the ground.
2.
Remove small limbs in one cut.
3.
Cut branches that have tension from the bottom to
the top to prevent pinching the saw chain or the
guide bar.
To buck a log
CAUTION:
Do not let the saw chain touch
the ground.
•
If the log has support along its full length, cut from
the top of the log (known as overbucking).
•
If the log has support on one end, cut 1/3 the
diameter from below the log (known as
underbucking).
•
If the log has support on the two ends, cut 1/3 the
diameter from the top. Complete the cut by
underbucking the lower 2/3 of the log to touch the
first cut.
•
If you buck a log on a slope, always stay on the
uphill side of the log. Cut through the log while you
keep complete control of the product. Then release
the cutting pressure near the end of the cut while
tightly holding the rear handle and front handle.
To change the power mode
The power mode of the product can be changed while
the product is in operation. There are 2 power modes:
1.
Standard mode
- Saves energy and maximizes run
time. Standard mode is applicable for most tasks.
Note:
The product is set to Standard mode when
started.
319 - 002 - 17.11.2017
13