ProForm 1110 E Elliptical English Manual - Page 14

Shield Cover 75 onto the Left and Right Shields - elliptical parts

Get ProForm 1110 E Elliptical PDF manuals and user guides View all ProForm 1110 E Elliptical manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

12. Apply grease to a Pedal Arm Axle (64). 12 Next, slide an M8 Washer (97) and an Axle Spacer (77) onto an M8 x 13mm Screw (82), and tighten the Screw a few turns into the Pedal Arm Axle (64). While a second person holds the front end of the Right Pedal Arm (58) inside the bracket on the Right Upper Body Leg (60), insert the Pedal Arm Axle (64) into both parts. Slide an M8 Washer (97) and an Axle Spacer 99 (77) onto another M8 x 13mm Screw (82), and tighten the Screw a few turns into the Pedal Arm Axle (64). Then, tighten both Screws at the same time. Repeat this step on the other side of the elliptical. See assembly step 5. Tighten the M10 x 25mm Screws (99). 82 97 77 60 Grease 64 77 97 58 82 13. Orient the Shield Cover (75) assembly as shown. 13 While a second person holds the Shield Cover (75) assembly near the Upright (4), connect the Fan Extension Wire (146) to the Fan Wire (136). Tip: Avoid pinching the wires. Press the Shield Cover (75) onto the Left and Right Shields (73, 74). 75 Avoid pinching the wires 4 73, 74 146 136 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
14
82
97
97
77
58
77
60
64
12. Apply grease to a Pedal Arm Axle (64).
Next, slide an M8 Washer (97) and an Axle
Spacer (77) onto an M8 x 13mm Screw (82), and
tighten the Screw a few turns into the Pedal Arm
Axle (64).
While a second person holds the front end of the
Right Pedal Arm (58) inside the bracket on the
Right Upper Body Leg (60), insert the Pedal Arm
Axle (64) into both parts.
Slide an M8 Washer (97) and an Axle Spacer
(77) onto another M8 x 13mm Screw (82), and
tighten the Screw a few turns into the Pedal Arm
Axle (64).
Then, tighten both Screws at the
same time.
Repeat this step on the other side of the
elliptical.
See assembly step 5.
Tighten the M10 x 25mm
Screws (99).
Grease
12
82
13
13. Orient the Shield Cover (75) assembly as shown.
While a second person holds the Shield Cover
(75) assembly near the Upright (4), connect the
Fan Extension Wire (146) to the Fan Wire (136).
Tip: Avoid pinching the wires.
Press the
Shield Cover (75) onto the Left and Right Shields
(73, 74).
75
4
73, 74
Avoid pinching
the wires
146
136
99