ProForm 920ci English Manual - Page 18

ProForm 920ci Manual

Get ProForm 920ci PDF manuals and user guides View all ProForm 920ci manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

49. Wrap the High Cable (72) around a 3 1/2" Pulley (24) as shown. Attach the Pulley, a Cable Trap (25), and an Angle Spacer (103) to the 3/8" x 4" Carriage Bolt (104) in the Press Base (6). Make sure the Angle Spacer is angled exactly as shown. Secure the Pulley with a 3/8" Nylon Jam Nut (63). Make sure the Cable Trap is oriented as shown. 49 63 24 25 72 103 6 50. Wrap the High Cable (72) around a 3 1/2" Pulley (24) in the direction shown. Attach the Pulley inside the indicated bracket on the Weight Base (5) with a 3/8" x 1 3/4" Bolt (57) and a 3/8" Nylon Locknut (50). Make sure that the Cable Trap is oriented as shown. 50 24 Bracket 57 72 50 5 51. Wrap the High Cable (72) over a 4 1/2" Pulley (102) in the direction shown. Attach the Pulley inside the indicated bracket on the Weight Top Frame (66) with a 3/8" x 2" Bolt (54) and a 3/8" Nylon Locknut (50). 51 66 Bracket 54 50 102 72 52. Attach the bolt at the end of the High Cable (72) to the remaining "U"-Bracket (97) with a 1/4" Flat Washer (71) and a 1/4" Nylon Locknut (68). Note: Do not completely tighten the Nylon Locknut; it should be threaded only two turns onto the end of the Cable, as shown in the inset drawing. Attach the "U"-Bracket (97) to the hole in the Long Weight Tube (96) with a 5/16" x 1 3/4" Bolt (60) and a 5/16" Nylon Locknut (64). Follow all four cables from end to end. Make sure that they rest in the grooves of the pulleys and that the cables and the pulleys move smoothly. 52 72 97 72 71 60 71 68 96 68 97 64 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
49. Wrap the High Cable (72) around a 3 1/2” Pulley (24)
as shown. Attach the Pulley, a Cable Trap (25), and
an Angle Spacer (103) to the 3/8” x 4” Carriage Bolt
(104) in the Press Base (6).
Make sure the Angle
Spacer is angled exactly as shown.
Secure the
Pulley with a 3/8” Nylon Jam Nut (63).
Make sure the
Cable Trap is oriented as shown.
50. Wrap the High Cable (72) around a 3 1/2” Pulley (24)
in the direction shown. Attach the Pulley inside the
indicated bracket on the Weight Base (5) with a 3/8”
x 1 3/4” Bolt (57) and a 3/8” Nylon Locknut (50).
Make sure that the Cable Trap is oriented as
shown.
50
72
5
50
57
24
24
63
6
103
25
72
51. Wrap the High Cable (72) over a 4 1/2” Pulley (102)
in the direction shown. Attach the Pulley inside the
indicated bracket on the Weight Top Frame (66) with
a 3/8” x 2” Bolt (54) and a 3/8” Nylon Locknut (50).
51
72
54
102
50
Bracket
Bracket
66
49
52. Attach the bolt at the end of the High Cable (72) to
the remaining “U”-Bracket (97) with a 1/4” Flat
Washer (71) and a 1/4” Nylon Locknut (68).
Note: Do
not completely tighten the Nylon Locknut; it
should be threaded only two turns onto the end
of the Cable, as shown in the inset drawing.
Attach the “U”-Bracket (97) to the hole in the Long
Weight Tube (96) with a 5/16” x 1 3/4” Bolt (60) and a
5/16” Nylon Locknut (64).
Follow all four cables from end to end. Make sure
that they rest in the grooves of the pulleys and
that the cables and the pulleys move smoothly.
64
68
96
71
72
97
60
52
72
97
71
68
18