Ridgid BS1400 Owners Manual - Page 3
General Safety Rules - tire
View all Ridgid BS1400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 3 highlights
GENERAL SAFETY RULES WARNING: n PROTECT YOUR HEARING. Wear hearing protection during extended periods of operation. Read and understand all instructions. Failure to follow all instructions listed below, may result in electric shock, fire and/or serious personal injury. READ ALL INSTRUCTIONS n KNOW YOUR POWER TOOL. Safe operation of this power tool requires that you read and understand this operator's manual and all labels affixed to the tool. Learn its applications and limitations as well as the potential hazards. n GUARD AGAINST ELECTRICAL SHOCK by preventing body contact with grounded surfaces such as pipes, radiators, ranges, refrigerator enclosures. n KEEP GUARDS IN PLACE and in good working order. Never operate the tool with any guard or cover removed. Make sure all guards are operating properly before each use. n SECURE WORK. Use clamps or a vise to hold the work when practical. It's safer than using your hand and frees both hands to operate the tool. n DO NOT OVERREACH. Keep proper footing and balance at all times. n MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. n DISCONNECT ALL TOOLS. When not in use, before servicing, or when changing attachments, all tools should be disconnected. n AVOID ACCIDENTAL STARTING. Be sure switch is off when plugging in any tool. n USE RECOMMENDED ACCESSORIES. Consult this operator's manual for recommended accessories. The use of improper accessories may cause risk of injury. n REMOVE ADJUSTING KEYS AND WRENCHES. Get n NEVER STAND ON TOOL. Serious injury could occur if the in the habit - before turning on tool - that hex keys and tool is tipped or if the bit is unintentionally contacted. adjusting wrenches are removed from tool. n CHECK DAMAGED PARTS. Before using the tool, a guard n KEEP THE WORK AREA CLEAN. Cluttered work areas and work benches invite accidents. n DO NOT USE IN DANGEROUS ENVIRONMENTS. Do not use power tools near gasoline or other flammable liquids, in damp or wet locations, or expose them to rain. Keep the work area well lighted. n KEEP CHILDREN AND VISITORS AWAY. All visitors should wear safety glasses and be kept a safe distance from work area. Do not let visitors contact tool or extension cord while operating. n MAKE WORKSHOP CHILDPROOF with padlocks and master switches or by removing starter keys. n DO NOT FORCE THE TOOL it will do the job better and safer at the rate for which it was designed. n USE THE RIGHT TOOL FOR THE JOB. Do not force the tool or attachment to do a job for which it was not designed for. Use it only the way it was intended. n USE THE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. Use only a cord heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A wire gage size (A.W.G.) of at least 16 is recommended for an extension cord 25 feet or less in length. If in doubt, use the next heavier gage. The smaller the gage number, the heavier the cord. n WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry that could get caught and draw you into moving parts. Nonslip footwear is recommended. Wear protective covering over long hair. or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting and any other conditions that may affect operation. A guard or other part that is damaged must be properly repaired or replaced by an authorized service center to avoid risk of personal injury. n NEVER LEAVE TOOL RUNNING UNATTENDED, TURN THE POWER OFF. Do not leave tool until it comes to a complete stop. n DO NOT ABUSE CORD. Never carry the tool by cord or yank to disconnect from receptacle. Keep cord from heat, oil, and sharp edges. n KEEP TOOL DRY, CLEAN, AND FREE FROM OIL AND GREASE. Always use a clean cloth when cleaning. Never use brake fluids, gasoline, petroleum-based products, or any solvents to clean tool. n STAY ALERT AND EXERCISE CONTROL. Watch what you are doing and use common sense. Do not operate tool when you are tired. Do not rush. n INSPECT TOOL CORDS AND EXTENSION CORDS PERIODICALLY and, if damaged, have repaired by a qualified service technician. Stay constantly aware of cord location and keep it well away from the rotating wheel. n NEVER USE IN AN EXPLOSIVE ATMOSPHERE. Normal sparking of the motor could ignite fumes. n USE ONLY OUTDOOR EXTENSION CORDS with approved ground connection that are intended for use outdoors and so marked. n ALWAYS WEAR SAFETY GLASSES WITH SIDE SHIELDS. Everyday eyeglasses have only impact resistant lenses; they are NOT safety glasses. n DO NOT USE TOOL IF SWITCH DOES NOT TURN IT ON AND OFF. Have defective switches replaced by an authorized service center. n PROTECT YOUR LUNGS. Wear a face or dust mask if n ALWAYS TURN SWITCH OFF before disconnecting it the operation is dusty. to avoid accidental starting. 3