Samsung 570DX User Manual (user Manual) (ver.1.0) (English) - Page 54

Color Temp, Brightness Sensor, Image Lock, Auto Adjustment, Signal Balance, Coarse, Position

Get Samsung 570DX - SyncMaster - 57inch LCD Flat Panel Display PDF manuals and user guides
UPC - 729507801155
View all Samsung 570DX manuals
Add to My Manuals
Save this manual to your list of manuals

Page 54 highlights

Note • If you adjust the picture by using the Color Control function, Color Tone will turn to the Custom mode. Color Temp [MENU ENTER ENTER ENTER] Color Temp is a measure of the 'warmth' of the image colors. (This function is only enabled if the Color Tone is set to Off.) Brightness Sensor [MENU ENTER ENTER ENTER] Brightness Sensor is to automatically detect distribution of inputted visual signal and adjust to create optimum brightness. 1) On 2) Off Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. (Available in PC, BNC mode only) 1) Coarse [MENU ENTER ENTER] → [ENTER ENTER] Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. 2) Fine [MENU ENTER ENTER ENTER ENTER] Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed). 3) Position [MENU ENTER ENTER ENTER ENTER] Adjusts the screen location horizontally and vertically. Auto Adjustment [MENU ENTER ENTER] The values of Fine, Coarse, Position are adjusted automatically. By changing the resolution in the control panel, the auto function is performed. (Available in PC, BNC mode only) [The direct button on the remote control is the 'AUTO' button.] Signal Balance This is used to make up for the weak RGB signal transmitted by a long signal cable. (Available in PC, BNC mode only)

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Note
•
If you adjust the picture by using the Color Control function, Color Tone will turn to the Custom mode.
Color Temp
[MENU]
→
[
∧
/
∨
]
→
[ENTER]
→
[
∧
/
∨
]
→
[ENTER]
→
[< / >]
→
[ENTER]
Color Temp is a measure of the 'warmth' of the image colors.
(This function is only enabled if the Color Tone is set to Off.)
Brightness Sensor
[MENU]
→
[
∧
/
∨
]
→
[ENTER]
→
[
∧
/
∨
]
→
[ENTER]
→
[< / >]
→
[ENTER]
Brightness Sensor is to automatically detect distribution of inputted visual signal and adjust to create optimum
brightness.
1) On
2) Off
Image Lock
Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with
jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse
adjustment and then use Fine again.
(Available in PC, BNC mode only)
1) Coarse
[MENU]
→
[
∧
/
∨
]
→
[ENTER]
→
[
∧
/
∨
]
→
[ENTER]
→
[ENTER]
→
[< / >]
→
[ENTER]
Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may
relocate it to the center using the horizontal control menu.
2) Fine
[MENU]
→
[
∧
/
∨
]
→
[ENTER]
→
[
∧
/
∨
]
→
[ENTER]
→
[
∧
/
∨
]
→
[ENTER]
→
[< / >]
→
[ENTER]
Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after
adjusting the frequency (clock speed).
3) Position
[MENU]
→
[
∧
/
∨
]
→
[ENTER]
→
[
∧
/
∨
]
→
[ENTER]
→
[
∧
/
∨
]
→
[ENTER]
→
[< / >] / [
∧
/
∨
]
→
[ENTER]
Adjusts the screen location horizontally and vertically.
Auto Adjustment
[MENU]
→
[
∧
/
∨
]
→
[ENTER]
→
[
∧
/
∨
]
→
[ENTER]
The values of Fine, Coarse, Position are adjusted automatically.
By changing the resolution in the control panel, the auto function is performed.
(Available in PC, BNC mode only)
[The direct button on the remote control is the '
AUTO
' button.]
Signal Balance
This is used to make up for the weak RGB signal transmitted by a long signal cable.
(Available in PC, BNC mode only)