Samsung DVE60A9900V User Manual - Page 28

Connect the angled end of the, two-thirds turn.

Get Samsung DVE60A9900V PDF manuals and user guides View all Samsung DVE60A9900V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

English Installation Using the short hose as an extension B A C 1. Close the cold water tap. If you have a washer's cold water hose attached to the cold water tap, unscrew and remove the hose. Then, connect the short hose (B) to the cold water tap. Turn the coupling by hand until it is tight. 2. Using pliers, tighten the coupling an additional twothirds turn. Do not overtighten. You can damage the coupling. 3. Connect the Y-connector (A) to the brass male end of the short hose. Turn the coupling by hand until it is tight. 4. Using pliers, tighten the coupling an additional twothirds turn. Do not overtighten. You can damage the coupling. 5. Connect the angled end of the water hoses (C) to the filling valve at the bottom rear of the dryer. Turn the coupling by hand until it is tight. 6. Using pliers, tighten the coupling an additional twothirds turn. Do not overtighten. You can damage the coupling. 7. If you detached the cold water hose from your washer, attach the hose to the free end of the Y-connector, tighten the coupling by hand until it is tight, and then, using a pliers, tighten an additional two-thirds turn. 8. Open the cold water tap, and then check for any leaks. 28 English Untitled-5 28 2021-05-25 5:20:39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
English
Installation
English
28
Using the short hose as an extension
B
A
C
1.
Close the cold water tap. If you have a washer’s cold
water hose attached to the cold water tap, unscrew
and remove the hose. Then, connect the
short hose
(B)
to the cold water tap. Turn the coupling by hand
until it is tight.
2.
Using pliers, tighten the coupling an additional two-
thirds turn. Do not overtighten. You can damage the
coupling.
3.
Connect the
Y-connector (A)
to the brass male end
of the short hose. Turn the coupling by hand until it
is tight.
4.
Using pliers, tighten the coupling an additional two-
thirds turn. Do not overtighten. You can damage the
coupling.
5.
Connect the angled end of the
water hoses (C)
to the
filling valve at the bottom rear of the dryer. Turn the
coupling by hand until it is tight.
6.
Using pliers, tighten the coupling an additional two-
thirds turn. Do not overtighten. You can damage the
coupling.
7.
If you detached the cold water hose from your
washer, attach the hose to the free end of the
Y-connector, tighten the coupling by hand until it is
tight, and then, using a pliers, tighten an additional
two-thirds turn.
8.
Open the cold water tap, and then check for any
leaks.
Untitled-5
28
2021-05-25
°° 5:20:39