Samsung DVE60A9900V User Manual - Page 31

Vent blockage test, Running the vent blockage test

Get Samsung DVE60A9900V PDF manuals and user guides View all Samsung DVE60A9900V manuals
Add to My Manuals
Save this manual to your list of manuals

Page 31 highlights

English Vent blockage test After the dryer is installed, run the Vent Blockage Test function to check if the duct system is properly installed. Vent Blockage Test automatically detects the status of the ducts and reports any blockage or problems. Proper ducting can reduce drying time and save energy. NOTE The Vent Blockage Test function must run when the dryer is cool. If the dryer warms up after the installation check, run the Air Fluff cycle for several minutes to reduce its internal temperature. Running the vent blockage test 1. Make sure the drum is empty, and then close the door. (If there are any clothes or other items in the drum, the test will not give accurate results.) 2. Tap to turn the dryer on, then simultaneously tap and hold Options for 3 seconds. 3. Turn the Navigation dial to select Vent Blockage Test, and then tap OK. Vent Blockage Test starts immediately. -- The test takes about 2 minutes and "Testing..." is displayed during the test. CAUTION Do not open the door during the test. NOTE If you have started other procedures before running Vent Blockage Test, the dryer will not enter the Vent Blockage Test mode. 4. After 2 minutes, when the test is complete, the results are displayed and the dryer sounds a tone. If status of the duct system is normal, an alarm triggers with the "No problems detected" message. If the duct system cannot exhaust properly, the check code appears, and the dryer sounds an alarm tone. For description about the code, see the "Installation check codes" section on page 32. If there are any other problems, an information code appears in the display. For description about the code, see the "Information codes" section on page 64. -- To stop or cancel Vent Blockage Test, tap to turn off your dryer. -- The results remain on the display for about 5 minutes and then automatically turn off. You can turn the results off immediately by tapping . NOTE • During or after the test, the internal drum is hot. Use caution to prevent burns. The Vent Blockage Test function is used to check for problems in the current duct system when the dryer is installed for the first time. • If the test result displays check code (the duct system is blocked ), refer to the "Ducting requirements" section on page 16 and the "Exhaust ducting guide" section below, and then take proper measures to correct any problems. If the test is suspended, it could result in incorrect results. Follow the proper procedures when testing the dryer. • Even if the test result is normal ("No problems detected"), the duct system could be blocked slightly. Properly install all duct work according to the installation instructions in this manual. English 31 Untitled-5 31 2021-05-25 5:20:39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
  • 219
  • 220
  • 221
  • 222
  • 223
  • 224
  • 225
  • 226
  • 227
  • 228
English
English
31
Vent blockage test
After the dryer is installed, run the Vent Blockage Test function to check if the duct system is properly
installed. Vent Blockage Test automatically detects the status of the ducts and reports any blockage or
problems. Proper ducting can reduce drying time and save energy.
NOTE
The Vent Blockage Test function must run when the dryer is cool. If the dryer warms up after the
installation check, run the
Air Fluff
cycle for several minutes to reduce its internal temperature.
Running the vent blockage test
1.
Make sure the drum is empty, and then close the door. (If there are any clothes or other items in the
drum, the test will not give accurate results.)
2.
Tap
to turn the dryer on, then simultaneously tap and hold
Options
for 3 seconds.
3.
Turn the
Navigation dial
to select
Vent Blockage Test
, and then tap
OK
. Vent Blockage Test starts
immediately.
-
The test takes about 2 minutes and "
Testing...
" is displayed during the test.
CAUTION
Do not open the door during the test.
NOTE
If you have started other procedures before running Vent Blockage Test, the dryer will not enter the Vent
Blockage Test mode.
4.
After 2 minutes, when the test is complete, the results are displayed and the dryer sounds a tone. If
status of the duct system is normal, an alarm triggers with the "
No problems detected
" message. If the
duct system cannot exhaust properly, the check code appears, and the dryer sounds an alarm tone. For
description about the code, see the “
Installation check codes
” section on page
32
.
If there are any other problems, an information code appears in the display. For description about the
code, see the “
Information codes
” section on page
64
.
-
To stop or cancel Vent Blockage Test, tap
to turn off your dryer.
-
The results remain on the display for about 5 minutes and then automatically turn off. You can turn
the results off immediately by tapping
.
NOTE
•
During or after the test, the internal drum is hot. Use caution to prevent burns. The Vent Blockage Test
function is used to check for problems in the current duct system when the dryer is installed for the first
time.
•
If the test result displays check code (the duct system is blocked ), refer to the “
Ducting requirements
”
section on page
16
and the “
Exhaust ducting guide
” section below, and then take proper measures to
correct any problems. If the test is suspended, it could result in incorrect results. Follow the proper
procedures when testing the dryer.
•
Even if the test result is normal (“
No problems detected
”), the duct system could be blocked slightly.
Properly install all duct work according to the installation instructions in this manual.
Untitled-5
31
2021-05-25
°° 5:20:39