Sanyo HD150 Owners Manual - Page 11

Connecting Projector

Get Sanyo HD150 - PLV - LCD Projector PDF manuals and user guides View all Sanyo HD150 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

CONNECTING PROJECTOR TERMINALS OF PROJECTOR This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired combinations of input sources just by changing Terminal Boards. For Terminal Boards, contact sales dealer where you purchased a projector. INPUT/OUTPUT TERMINALS 3 TERMINAL SLOTS (Factory set) SERIAL PORT IN SDI IN1 SDI IN2 SDI OUT SERIAL PORT OUT R/C JACK USB AUDIO OUT R L RESET (MONO) R/Pr G/Y B/Pb H/HV V AUDIO R L CONTROL PORT (MONO) DVI AUDIO CONTROL PORT R L (MONO) INPUT 4 INPUT 3 INPUT 2 INPUT 1 SDI Terminal 5 BNC Terminal DVI Terminal REPLACEMENT OF TERMINAL NOTE; When replacement of terminal board, MAIN ON/OFF switch should be OFF position. 1 Remove 2 Screws on terminal. 2 Pull out terminal by holding handle. 3 Replace terminal. Insert terminal along Guide to fit Plug into Socket. 4 Tighten screws to secure terminal. NOTES ON ORDERING OR USING OPTIONAL INTERFACE BOARD When ordering or using Optional Interface Board (Terminal Board), contact your sales dealer. When contacting the sales dealer, tell the Optional Control Number (Op.cont.No.) in the menu that is located under Language Select Menu. (See page 37.) Plug Screws Guide Socket Figure shows DVI terminal. 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
11
CONNECTING PROJECTOR
TERMINALS OF PROJECTOR
This projector applies various input/output terminals and 4 terminal slots for expansion to tune to diversity of signals from
computers and video equipment. 4-built-in Terminal Slots enable you to arrange desired combinations of input sources just
by changing Terminal Boards.
For Terminal Boards, contact sales dealer where you purchased a projector.
Pull out terminal by holding handle.
Remove 2 Screws on terminal.
1
2
REPLACEMENT OF TERMINAL
Tighten screws to secure terminal.
Replace terminal. Insert terminal along Guide to fit Plug
into Socket.
3
4
INPUT 1
INPUT 2
INPUT 3
DVI
AUDIO
CONTROL PORT
CONTROL PORT
AUDIO
R/Pr
G/Y
B/Pb
H/HV
V
(MONO)
(MONO)
R
L
R
L
(MONO)
AUDIO OUT
R
L
R/C JACK
USB
SERIAL PORT IN
SERIAL PORT OUT
RESET
INPUT 4
SDI IN1
SDI IN2
SDI OUT
INPUT/OUTPUT
TERMINALS
Screws
Guide
Socket
Plug
Figure shows DVI terminal.
SDI Terminal
5 BNC Terminal
DVI Terminal
3 TERMINAL SLOTS (Factory set)
NOTES ON ORDERING OR USING
OPTIONAL INTERFACE BOARD
When ordering or using Optional Interface Board
(Terminal Board), contact your sales dealer. When con-
tacting the sales dealer, tell the Optional Control
Number (Op.cont.No.) in the menu that is located under
Language Select Menu. (See page 37.)
NOTE; When replacement of terminal board, MAIN
ON/OFF switch should be OFF position.