Sanyo PLC-XP200L Instruction Manual, PLC-XP200L - Page 85

Serial Control Interface, Operation

Get Sanyo PLC-XP200L - XGA LCD Projector PDF manuals and user guides
UPC - 086483072208
View all Sanyo PLC-XP200L manuals
Add to My Manuals
Save this manual to your list of manuals

Page 85 highlights

Appendix Serial Control Interface This projector provides a function to control and monitor the projector's operations by using the RS-232C serial port. Operation 1 Connect a RS-232C serial cross cable to CONTROL PORT on the projector and serial port on the PC. (See p.22) 2 Launch a communication software provided with PC and setup the communication condition as follows: Baud rate Parity check Stop bit Flow control Data bit : 9600 / 19200 bps : none : 1 : none : 8 ✔Note: • The default of the baud rate is set to 19200 bps. If an error occurs in the communication, change the serial port and the communication speed (baud rate). 3 Type the command for controlling the projector and then enter the "Enter" key. Example When you want to change the input to INPUT 2, Type 'C' '0' '6' 'Enter'. ✔Note: • Enter with ASCII 64-byte capital characters and onebyte characters. 85

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
85
Serial Control Interface
Appendix
This projector provides a function to control and monitor the projector's operations by using the RS-232C serial
port.
Connect a RS-232C serial cross cable to CONTROL
PORT on the projector and serial port on the PC.
(See p.22)
Launch a communication software provided with PC
and setup the communication condition as follows:
1
2
3
Baud rate
: 9600 / 19200 bps
Parity check
: none
Stop bit
: 1
Flow control
: none
Data bit
: 8
Type the command for controlling the projector and
then enter the "Enter" key.
Example
When you want to change the input to INPUT 2, Type
'C' '0' '6' 'Enter'.
✔
Note:
•
Enter with ASCII 64-byte capital characters and one-
byte characters.
✔
Note:
• The default of the baud rate is set to 19200 bps. If an
error occurs in the communication, change the serial
port and the communication speed (baud rate).
Operation