Schwinn 810 Treadmill Assembly and Owners Manual - Page 40

If you used spray lubricant, wait 5 minutes before turning on power to the machine to allow

Get Schwinn 810 Treadmill PDF manuals and user guides View all Schwinn 810 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 40 highlights

2. Unplug the treadmill fully from the wall outlet, and remove the power cord from the machine. To reduce the risk of electrical shock, always unplug the power cord and wait 5 minutes before cleaning, maintaining or repairing this machine. Place the power cord in a secure location. Note: Make sure the treadmill is located on a surface that is easy to clean. 3. Apply a few drops of the lubricant on the deck below the belt. Carefully lift the belt and apply a few drops of the lubri- cant the entire width of the belt. A very thin layer of silicone lubricant on the entire deck below the belt is desired. NOTICE: Always use a 100% pure silicone lubricant. Do not use a degreaser like WD-40® as this could seriously im- pact performance. We can recommend that you use the following: • 100% pure silicone, available at most hardware and auto parts stores. • Lube-N-Walk® Treadmill Lubrication Kit, available from your local specialty fitness dealer or Nautilus, Inc. Silicone lubricant is not intended for human consumption. Keep out of reach of children. Store in a safe place. 4. Manually rotate the belt 1/2 of the length of the belt and apply lubricant again. If you used spray lubricant, wait 5 minutes before turning on power to the machine to allow the aerosol to dissipate. 5. Connect the power cord back into the machine and then into the wall outlet. 6. Turn on the power to the machine with the power switch. 7. Stay to one side of your machine and start the belt at the slowest speed. Let the belt operate for approximately 15 seconds. Be sure not to touch the walking belt or step on the power cord. Keep bystanders and children away from the product you are servicing at all times. 8. Switch off your machine. 9. Take care to clean up any excess lubricant from the deck. To decrease the possibility of slipping, be sure the deck area is free from grease or oil. Clean off any excess oil from the machine surfaces. As you use your fitness machine, the Console will show "LUBRICATE BELT" followed by "REVIEW USER MANUAL" at set times. This is only a reminder and should be added to your inspection schedule. Only apply lubricant as necessary. Push any button to accept the reminder. 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
40
2.
Unplug the treadmill fully from the wall outlet, and remove the power cord from the machine.
To reduce the risk of electrical shock, always unplug the power cord and wait 5 min
-
utes before cleaning, maintaining or repairing this machine. Place the power cord in a
secure location.
Note:
Make sure the treadmill is located on a surface that is easy to clean.
3.
Apply a few drops of the lubricant on the deck below the belt. Carefully lift the belt and apply a few drops of the lubri-
cant the entire width of the belt. A very thin layer of silicone lubricant on the entire deck below the belt is desired.
NOTICE:
Always use a 100% pure silicone lubricant. Do not use a degreaser like WD-40
®
as this could seriously im-
pact performance. We can recommend that you use the following:
• 100% pure silicone, available at most hardware and auto parts stores.
• Lube-N-Walk
®
Treadmill Lubrication Kit, available from your local specialty fitness dealer or Nautilus, Inc.
Silicone lubricant is not intended for human consumption. Keep out of reach of children. Store in a safe
place.
4.
Manually rotate the belt 1/2 of the length of the belt and apply lubricant again.
If you used spray lubricant, wait 5 minutes before turning on power to the machine to allow the aerosol to
dissipate.
5.
Connect the power cord back into the machine and then into the wall outlet.
6.
Turn on the power to the machine with the power switch.
7.
Stay to one side of your machine and start the belt at the slowest speed. Let the belt operate for approximately 15
seconds.
Be sure not to touch the walking belt or step on the power cord. Keep bystanders and children away from
the product you are servicing at all times.
8.
Switch off your machine.
9.
Take care to clean up any excess lubricant from the deck.
To decrease the possibility of slipping, be sure the deck area is free from grease or oil. Clean off any excess
oil from the machine surfaces.
As you use your fitness machine, the Console will show “LUBRICATE BELT” followed by “REVIEW USER MANUAL” at
set times. This is only a reminder and should be added to your inspection schedule. Only apply lubricant as necessary.
Push any button to accept the reminder.