Schwinn 810 Treadmill Assembly and Owners Manual - Page 9

Before Assembly

Get Schwinn 810 Treadmill PDF manuals and user guides View all Schwinn 810 Treadmill manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

SPECIFICATIONS Power Requirements: 120V 220V Operational Voltage: 110-127V AC, 60Hz 220V - 240V AC, 50/60Hz Operating Current: 15 A 8 A Maximum User Weight: Total Surface Area (footprint) of equipment: Maximum Inclined Deck Height: Machine Weight: 125 kg (275 lbs) 15,848 cm2 40 cm (15.8 inches) 70.3 kg (155 lbs) 144 cm (56.7") Sound Emission: Less than 70 db average without load. Noise emission under load is higher than without load. 90.3 cm (35.6") 175.5 cm (69.1") DO NOT dispose of this product as refuse. This product is to be recycled. For proper disposal of this product, please follow the prescribed methods at an approved waste center. 153 cm (60.2") Before Assembly Select the area where you are going to set up and operate your machine. For safe operation, the location must be on a hard, level surface. Allow a minimum workout area of 190.3 cm x 376.2 cm (74.9" x 148.1"). Be sure that the workout space you are utilizing has adequate height clearance, taking into consideration the height of the user and the maximum incline of the machine. Basic Assembly Follow these basic points when you assemble your machine: 3.76 m ( 148.1 in ) • Read and understand the "Important Safety Instructions" before assembly. • Collect all the pieces necessary for each assembly step. • Using the recommended wrenches, turn the bolts and nuts to the right (clockwise) to tighten, and the left (counterclockwise) to 1.9 m ( 74.9 in ) loosen, unless instructed otherwise. • When attaching 2 pieces, lightly lift and look through the bolt holes to help insert the bolt through the holes. • The assembly requires 2 people. • Do not use any power tools for assembly. 0.5 m ( 19.7 in ) 0.5 m ( 19.7 in ) 100.3 cm (39.5") 2 m ( 79 in ) Machine Mat The Schwinn™ Machine Mat is an optional accessory that helps keep your workout area clear and adds a layer of protection to your floor. The rubber machine mat provides a non-slip, rubber surface which limits static discharge and reduces the possibility of display errors. If possible, put your Schwinn™ Machine Mat in your selected workout area before you begin assembly. To order the optional machine mat, contact Customer Service (if purchased in US/Canada) or your local distributor (if purchased outside US/Canada). 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
9
SPECIFICATIONS
Power Requirements:
120V
220V
Operational Voltage:
110-127V AC, 60Hz
220V - 240V AC, 50/60Hz
Operating Current:
15 A
8 A
Maximum User Weight:
125 kg (275 lbs)
Total Surface Area (footprint) of equipment:
15,848 cm
2
Maximum Inclined Deck Height:
40 cm (15.8 inches)
Machine Weight:
70.3 kg (155 lbs)
Sound Emission:
Less than 70 db average without load. Noise emission
under load is higher than without load.
DO NOT dispose of this product as refuse. This product is to be
recycled. For proper disposal of this product, please follow the
prescribed methods at an approved waste center.
90.3 cm
(35.6”)
175.5 cm
(69.1”)
100.3 cm
(39.5”)
144 cm
(56.7”)
153 cm
(60.2”)
Before Assembly
Select the area where you are going to set up and operate your machine.
For safe operation, the location must be on a hard, level surface. Allow a
minimum workout area of 190.3 cm x 376.2 cm (74.9” x 148.1”). Be sure that
the workout space you are utilizing has adequate height clearance, taking
into consideration the height of the user and the maximum incline of the machine.
Basic Assembly
Follow these basic points when you assemble
your machine:
• Read and understand the “Important Safety
Instructions” before assembly.
• Collect all the pieces necessary for each
assembly step.
• Using the recommended wrenches, turn
the bolts and nuts to the right (clockwise) to
tighten, and the left (counterclockwise) to
loosen, unless instructed otherwise.
• When attaching 2 pieces, lightly lift and look
through the bolt holes to help insert the bolt
through the holes.
•
The assembly requires 2 people.
• Do not use any power tools for assembly.
Machine Mat
The Schwinn™ Machine Mat is an optional accessory that helps keep your workout area clear and adds a layer of
protection to your floor. The rubber machine mat provides a non-slip, rubber surface which limits static discharge and
reduces the possibility of display errors. If possible, put your Schwinn™ Machine Mat in your selected workout area before
you begin assembly.
To order the optional machine mat, contact Customer Service (if purchased in US/Canada) or your local distributor (if
purchased outside US/Canada).
3.76 m ( 148.1 in )
1.9 m
( 74.9 in )
2 m
( 79 in )
0.5 m
( 19.7 in )
0.5 m
( 19.7 in )