Sharp CD-CH1500 CDCH1500 Operation Manual - Page 26

Advanced Features

Get Sharp CD-CH1500 PDF manuals and user guides View all Sharp CD-CH1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Timer and Sleep Operation (continued) 6 Turn the jog dial to specify the minute and within 10 seconds, press the ENTER button. 11 Press the POWER button to enter the timer stand-by mode. Advanced Features - Timer and Sleep Operation - 7 Turn the jog dial to specify the hour to stop and within 10 sec- onds, press the ENTER button. 8 Turn the jog dial to specify the minute and within 10 seconds, press the ENTER button. Start time End time 9 Adjust the volume using the VOLUME buttons. Do not turn the volume up too high. 10 Press the CD, TUNER (BAND) or TAPE button to select the de- sired function. To select the timer playback source : CD, TUNER (BAND) or TAPE. To select the timer recording source : TUNER (BAND). To cancel the timer playback or timer recording: 1. Press the POWER button to turn the power on. 2. Press the MENU button. 3. Turn the jog dial to select "TIMER OFF" and then press the ENTER button. To check the setting time: 1. Press the POWER button to turn the power on. 2. Press the MENU button. 3. Turn the jog dial to select "TIMER PLAY" or "TIMER REC" and then press the ENTER button. 4. Press the POWER button to enter the timer stand-by mode. 12 When the preset time is reached, playback or recording will start. The volume will increase gradually until it reaches the volume you were listening to before your system enters the timer stand-by mode. 13 When the timer end time is reached, the system will enter the power stand-by mode automatically. If you press any button during timer operation, the timer mode is canceled and playback or recording will last even when the end time is reached. To reset or change the timer setting: Perform "Timer playback or Timer recording" from the beginning. Notes: q Once the time is set, the setting will be retained until a new time is entered. q When performing timer playback or recording using another unit connected to the AUX IN jacks, select "AUX" in step 10. At this time, only this stereo system will enter the power stand-by mode automatically. (Another unit will not be turned off.) 26

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
26
6
Turn the jog dial to specify the minute and within 10 seconds,
press the ENTER button.
7
Turn the jog dial to specify the hour to stop and within 10 sec-
onds, press the ENTER button.
8
Turn the jog dial to specify the minute and within 10 seconds,
press the ENTER button.
9
Adjust the volume using the VOLUME buttons.
Do not turn the volume up too high.
10
Press the CD, TUNER (BAND) or TAPE button to select the de-
sired function.
To select the timer playback source : CD, TUNER (BAND) or TAPE.
To select the timer recording source : TUNER (BAND).
Advanced Features
– Timer and Sleep Operation –
Timer and Sleep Operation (continued)
11
Press the POWER button to enter the timer stand-by mode.
To cancel the timer playback or timer recording:
1.
Press the POWER button to turn the power on.
2.
Press the MENU button.
3.
Turn the jog dial to select “TIMER OFF” and then press the ENTER button.
To check the setting time:
1.
Press the POWER button to turn the power on.
2.
Press the MENU button.
3.
Turn the jog dial to select “TIMER PLAY” or “TIMER REC” and then press
the ENTER button.
4.
Press the POWER button to enter the timer stand-by mode.
12
When the preset time is reached, playback or recording will start.
The volume will increase gradually until it reaches the volume you were listen-
ing to before your system enters the timer stand-by mode.
13
When the timer end time is reached, the system will enter the
power stand-by mode automatically.
If you press any button during timer operation, the timer mode is canceled and
playback or recording will last even when the end time is reached.
To reset or change the timer setting:
Perform “Timer playback or Timer recording” from the beginning.
Notes:
●
Once the time is set, the setting will be retained until a new time is entered.
●
When performing timer playback or recording using another unit connected to the
AUX IN jacks, select “AUX” in step 10. At this time, only this stereo system will enter
the power stand-by mode automatically. (Another unit will not be turned off.)
Start time
End time