Sharp DV-NC150U DV-NC150U Operation Manual - Page 15

Hint for Timer Recording • If there is a power failure or the VCR/DVD has been unplugged for more than 30 seconds, the clock setting and all timer settings will be lost. • If a tape is not in the VCR/DVD or does not have the record tab, the TIMER and lights flash and timer recording cannot be performed. Please insert a recordable tape. • If a tape ends during timer recording, the VCR will stop, eject the tape, and switch to the DVD mode automatically as the TIMER and lights flash. (If the DVD power is off, the VCR will become STANDBY status). • When all timer recordings are finished, the TIMER and lights will flash. • When timer recordings are set, theTIMER and lights will appears. To use the VCR as usual until the time for the recording, press the SUBTITLE/T-SET button so that the TIMER and lights disappear. Press the VCR/TV button to choose the VCR position. Select either VCR or DVD mode, then continue with the other features as described in this manual. If you want to use the DVD player during a VCR timer recording or while the TIMER and lights are on or flashes. • You can use the DVD player while the TIMER and lights are on or flashes, or during a timer recording. Press the POWER button to turn on the VCR/DVD. Press the DVD button on the remote control to choose DVD mode, then continue with the other DVD features as described in this manual. You don't have to set the TIMER off to use the DVD only. Copying a Video Tape Warning: Unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. (Back of TV) 1) Insert a pre-recorded tape into the playing VCR. (Back of another source) (Back of Recording VCR/DVD*) or AUDIO OUT COMPONENT VIDEO OUT L DVD/VCR VCR AUDIO OUT AUDIO IN Y L L R CB R R VIDVEOIDOUETO OVIUDETO IN CR 1 ANT-IN DIGITAL AUDIO OUT Connect DVD AUSD-VIOIDEO OUOTUT COMPONENT VIDEO OUT Y DVD/VCR AUDIO OUT L VCR AUDIO IN L L ANT-OUT COAXIAL R CB R R VIDEO OUT VIDEO IN CR 2 ANT-IN Connect ANT-OUT 2) Insert a tape with its record tab into the recording VCR/DVD. 3) Press the SPEED button on the remote control of the recording VCR/DVD to select the desired recording speed (SP/SLP). Round Coaxial cable 4) Select the "L1" or "L2" position on the recording VCR/DVD. Audio/Video cables (supplied) (supplied) *Front input jacks are also available • To use the input jacks on the back of this unit, select "L1" position by pressing [0], [0], [1] on the remote Hint control or the SKIP/CH. (K/L) buttons. • To use the input jacks on the front of this unit, select • For best results during dubbing, use the front panel controls whenever possible. The remote control might affect another source's operation. "L2" position by pressing [0], [0], [2] on the remote control or the SKIP/CH. (K/L) buttons. • Always use video-quality shielded cables with RCA-type connectors. Standard audio 5) Press the REC button on the recording VCR/DVD. cables are not recommended. • You can use a video disc player, satellite receiver, or other audio/video component with A/V outputs. • "L1" or "L2" is found before the lowest memorized channel. (Example: CH02) • "L2" input jacks are on the front of this VCR/DVD. 6) Begin playback of the tape in another source. 7) To stop recording, press the STOP/EJECT button on the recording VCR/DVD, then stop playback of the tape in another source. MTS System (Multi-Channel Television Sound) VCR Functions When You Receive or Record a Program Broadcast in MTS • When you receive a broadcast on the VCR, you can check the type of the broadcast by pressing the DISPLAY button. • When "TV STEREO" or "SAP" selection is valid, select them by following steps. This selection is needed when you record the program. • SAP means Second Audio Program (usually second language). VCR 1 MENU or VCR -MENU- TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP CLOCK SET LANGUAGE SELECT AUDIO OUT B TV STEREO [ON] SAP Select "TV STEREO" or "SAP" 2 To exit the menu. CLEAR/ C.RESET Display on the TV screen -None- STEREO Type of broadcast Regular (monaural audio) Stereo broadcast SAP Bilingual broadcast STEREO SAP Stereo & Bilingual broadcast STEREO/SAP Selection -Invalid- -Invalid- TV STEREO (main audio program) SAP (second audio program) TV STEREO (stereo main audio program) SAP (second audio program) When You Play Back a Tape Recorded in Hi-Fi Stereo • If you have connected a stereo TV to this VCR/DVD, select "STEREO". • If you have connected a monaural TV to this VCR/DVD, select "MONO". Your Selection Type of recorded tape non Hi-Fi tapes Hi-Fi tapes recorded in Hi-Fi stereo Hi-Fi tapes recorded main audio program STEREO L-channel R-channel Monaural Monaural L R Main audio Main audio program program MONO Monaural L+R Main audio program Hi-Fi tapes recorded second audio program Second audio Second audio Second audio program program program - 15 - VCR 1 MENU or VCR -MENU- TIMER PROGRAMMING AUTO REPEAT [OFF] CHANNEL SET UP CLOCK SET LANGUAGE SELECT B AUDIO OUT TV STEREO [ON] SAP 2 or AUDIO OUT B HIFI MONO [ON] Select "HIFI" or "MONO" 3 To exit the menu. CLEAR/ C.RESET EN