Sharp VL-NZ50U Operation Manual - Page 20

Preparation - model

Get Sharp VL-NZ50U - MiniDV Compact Digital Viewcam PDF manuals and user guides
UPC - 074000352957
View all Sharp VL-NZ50U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Preparation PPrerpearpataionration Attaching and Removing the Battery Pack Attaching Power switch Removing 1 Make sure that the Power switch is set to OFF. 2 Rotate the monitor section of the camcorder (1), then press the battery release (2). Slide the battery pack in the direction of the arrow and take it out (3). 1 Make sure that the Power switch is set to OFF. 2 Align the = mark on the side of the battery pack with the = mark on the camcorder (1), and slide the battery pack in the direction of the arrow completely until it locks into place (2). Battery release Cautions: • BEFORE REMOVING THE BATTERY PACK, ALWAYS STOP RECORDING OR PLAYBACK AND TURN THE POWER OFF. Removing the battery pack while shooting or during playback may damage the tape by causing it to wrap around the video head drum. • Remove the battery pack from the camcorder if you will not use the camcorder for a long period of time. • Make sure that the battery pack is firmly attached during operation. If it is not, the battery pack may come off or camcorder operation may fall because of the poor contact pressure. • To prevent damage to the battery pack when removing, be sure to firmly hold the battery pack while pressing the release. • Use only SHARP model BT-L225 or BT-L445 battery packs with this camcorder. Use of other batteries may create a risk of fire or explosion. 7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
7
Preparation
Preparation
Removing
1
Make sure that the Power switch is set
to OFF.
2
Rotate the monitor section of the
camcorder (
1
), then press the battery
release (
2
). Slide the battery pack in
the direction of the arrow and take it out
(
3
).
Cautions:
•
BEFORE REMOVING THE BATTERY PACK,
ALWAYS STOP RECORDING OR PLAYBACK
AND TURN THE POWER OFF.
Removing the
battery pack while shooting or during playback
may damage the tape by causing it to wrap
around the video head drum.
• Remove the battery pack from the camcorder if
you will not use the camcorder for a long period
of time.
• Make sure that the battery pack is firmly
attached during operation. If it is not, the battery
pack may come off or camcorder operation may
fall because of the poor contact pressure.
• To prevent damage to the battery pack when
removing, be sure to firmly hold the battery pack
while pressing the release.
•Use only SHARP model BT-L225 or BT-L445
battery packs with this camcorder. Use of other
batteries may create a risk of fire or explosion.
Attaching and Removing
the Battery Pack
Attaching
1
Make sure that the Power
switch is set to OFF.
2
Align the
=
mark on the side of the
battery pack with the
=
mark on the
camcorder (
1
), and slide the battery
pack in the direction of the arrow
completely until it locks into place (
2
).
Battery release
Power switch