Sony BRC300 Operating Instructions - Page 16

Sony BRC300 Manual

Get Sony BRC300 PDF manuals and user guides View all Sony BRC300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

M VISCA RS-232C IN connector Connect to the RM-BR300 Remote Control Unit (not supplied). When you connect multiple cameras, connect it to the VISCA RS-232C OUT connector of the previous camera in the daisy chain connection. N VISCA RS-232C OUT connector When you connect multiple cameras, connect it to the VISCA RS-232C IN connector of the next camera in the daisy chain connection. O DC IN 12V connector Connect the supplied AC power adaptor. P Card slot Insert an optional interface card such as BRBK301, BRBK-302 and BRBK-303. The slot cover is attached to the camera at the factory. Bottom qj qk ql Setting of the BOTTOM switches 1 2 3 4 5 1 2 3 4 O N 1 2 3 4 O N Overview 1 Switch 1 (No Connection) Always keep it OFF. 2 Switch 2 (RS-232C/RS-422 selector) Set to ON for RS-422, or OFF for RS-232C. 3 Switch 3 (Communication baud rate selector) Set to ON for 38400bps, or OFF for 9600bps. 4 Switch 4 (Infrared signal output switch) Set to ON to enable an infrared signal output, or OFF to disable the output. 5 Camera address selectors Set the address of the camera. Normally set to "0". With this setting, addresses are assigned to the cameras automatically in the connected order by pressing the POWER button while holding down the RESET button on the RMBR300 Remote Control Unit. You can assign the camera address "1" to "7" manually by setting these selectors as follows: Camera address Switch 1 Switch 2 Switch 3 0 1 2 3 4 5 6 7 OFF ON OFF ON ON OFF ON ON OFF ON ON ON ON OFF OFF ON OFF OFF ON Q Ceiling bracket mounting screw holes When you install the camera to the ceiling, secure the supplied ceiling bracket to these holes using the supplied four screws. For installation, see "Installing the Camera on the Ceiling" on page 43. R Tripod screw holes (1/4-20UNC) When you install the camera to a tripod, secure the tripod to these holes. S BOTTOM switches Used for the RS-232C/RS-422 selection, baud rate selection, remote control signal output on/off and camera address setting. For details, see "Setting of the BOTTOM switches" on page 16. OFF OFF OFF OFF ON Note Switch 4 is not used. 16 Location and Function of Parts

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
Overview
Location and Function of Parts
16
M
VISCA RS-232C IN connector
Connect to the RM-BR300 Remote Control Unit
(not supplied).
When you connect multiple
cameras, connect it to the VISCA RS-232C OUT
connector of the previous camera in the daisy chain
connection.
N
VISCA RS-232C OUT connector
When you connect multiple cameras, connect it to
the VISCA RS-232C IN connector of the next
camera in the daisy chain connection.
O
DC IN 12V connector
Connect the supplied AC power adaptor.
P
Card slot
Insert an optional interface card such as BRBK-
301, BRBK-302 and BRBK-303.
The slot cover is attached to the camera at the
factory.
Bottom
Q
Ceiling bracket mounting screw holes
When you install the camera to the ceiling, secure
the supplied ceiling bracket to these holes using the
supplied four screws.
For installation, see “Installing the Camera on the
Ceiling” on page 43.
R
Tripod screw holes (1/4-20UNC)
When you install the camera to a tripod, secure the
tripod to these holes.
S
BOTTOM switches
Used for the RS-232C/RS-422 selection, baud rate
selection, remote control signal output on/off and
camera address setting.
For details, see “Setting of the BOTTOM switches”
on page 16.
Setting of the BOTTOM switches
1
Switch 1 (No Connection)
Always keep it OFF.
2
Switch 2 (RS-232C/RS-422 selector)
Set to ON for RS-422, or OFF for RS-232C.
3
Switch 3 (Communication baud rate selector)
Set to ON for 38400bps, or OFF for 9600bps.
4
Switch 4 (Infrared signal output switch)
Set to ON to enable an infrared signal output, or
OFF to disable the output.
5
Camera address selectors
Set the address of the camera.
Normally set to "0".
With this setting, addresses are
assigned to the cameras automatically in the
connected order by pressing the POWER button
while holding down the RESET button on the RM-
BR300 Remote Control Unit.
You can assign the camera address "1" to "7"
manually by setting these selectors as follows:
Note
Switch 4 is not used.
qk
qj
ql
Camera
address
0
1
2
3
4
5
6
7
Switch 1
OFF
ON
OFF
ON
OFF
ON
OFF
ON
Switch 2
OFF
OFF
ON
ON
OFF
OFF
ON
ON
Switch 3
OFF
OFF
OFF
OFF
ON
ON
ON
ON
O
N
1
2
3
4
O
N
1
2
3
4
2
1
4
5
3