Sony PDW700 User Manual (PDW-700 / PDW-F800 Operation Manual for Firmware Vers - Page 33

Chapter 1 Overview d Viewfinder screen e VTR SAVE indicator This indicator lights when the VDR SAVE/STBY switch is set to SAVE, putting the VDR into power save mode. f ! (warning) indicator This indicator lights when any of the following conditions occurs with the corresponding item set to ON on the '!' LED page of the OPERATION menu. • The gain is set to other than 0 dB. • The SHUTTER selector is not set to the standard setting. 1), 2) • The WHITE BAL switch is set to PRST. • ATW is enabled. • The lens extender is used. • The FILTER selector is set to other than ND:1. • The reference value of auto iris adjustment is not the standard value. For the PDW-F800, lighting-up conditions of each item can be set on the '!' LED STD page of the OPERATION menu. 1) The standard SHUTTER setting differs as follows, depending on the recording format. 1080/50i, 1080/59.94i, 720/50P, 720/59.94P (SCAN MODE: 59.9P): The SHUTTER selector is set to OFF. 1080/23.98P, 720/59.94P (SCAN MODE: 23.9P): 1/48 shutter is ON. 1080/25P: 1/50 shutter is ON. 1080/29.97P: 1/60 shutter is ON. 2) For the PDW-F800, when SHUTTER SELECT on the SHUTTER SELECT page of the MAINTENANCE menu is set to DEGREE, the standard setting is "SHUTTER selector: OFF", regardless of the recording format. Layout of the status display on the viewfinder screen The viewfinder screen displays not only the video picture but also characters and messages indicating the camcorder settings and operating status, a center marker, a safety zone marker, etc. When the menu screen is not displayed and the DISPLAY of the DISPLAY/ASPECT switch is set to on, the items for which an ON setting was made on the VF DISP 1, VF DISP 2, or VF DISP 3 page of the OPERATION menu or with related switches are displayed at the top and bottom of the screen. The messages that give details of the settings and adjustment progress and results can also be made to appear for about three seconds while settings are being changed, during adjustment, and after adjustment. For details about the display item selection, see "Selecting the display items" on page 201. For details about setting change and adjustment progress messages, see "Change confirmation/ adjustment progress messages" on page 202. For details about marker display, see "Setting the marker display" on page 203. All items that can be displayed on the viewfinder screen are shown below. Top of viewfinder screen 12 3 4 5 6 7 8 9 59.9 i[30] E X Z 99 HD422 50 13.9 K + CONT FAN W1 2 E0001:001/004 13.4V DC IN 35-30 REC2 5600 1 W:A WHITE:NG LEVEL TOO HIGH TCG 01:23:45:15 LOW LIGHT 18 dB 1/ 2000 1 2 35 - 30 EXT HDSDI 125C F1.7 0qa qs a Color temperature Displays a color temperature calculated from the gain of R and B, in the range 0.0 K to 99.9 K (in steps of 0.1 K). The +/- signs may be displayed depending on the OFFSET WHT setting (see page 212). No display: OFFSET WHT is OFF +: The value of OFFSET WHT is greater than 3200K. -: The value of OFFSET WHT is less than 3200K. b Video format Indicates the format of video being currently played back or recorded (see page 57). The video aspect ratio (16:9 or 4:3) can also be displayed when the recording format is set to IMX 50, IMX 40, IMX 30, or DVCAM. Locations and Functions of Parts and Controls 33