Sony SLV-272 Operating Instructions - Page 10

Connect, Cable, System, Before, Begin

Get Sony SLV-272 PDF manuals and user guides View all Sony SLV-272 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

Connections In order to watch the playback picture on the TV screen and receive TV programs on this VCR, you must connect the VCR and the TV properly. The connection between the two units varies depending upon the type of TV and antenna that you have. We will show you here some typical ways you can make this connection with the supplied accessories. Before You Begin • Turn off the power of the VCR and TV. • Disconnect the AC power cord of the VCR and TV from the wall outlet. • Do not connect the AC power cords until all of the connections are completed. To Connect a Cable-TV System If your TV has a built-in CATV decoder CATV 75-ohm coaxial cable Disconnect the CATV cable from the TV. 0 VHF/UHF TV UHF VHF CATV cable If your TV does not have a built-in CATV decoder CATV 75-ohm coaxial cable Disconnect the CATV cable from the TV. CATV channel msesime converter VHF/UHF TV CATV channel converter 00 UHF monsium461 VHF TV CATV cable OMMINIIIIIIMININk Note to CATV system installer in the U.S.A. This reminder is provided to call the cable TV system installer's attention to Article £320-22 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical. 10 Caution Connections between the recorder VHF/UHF OUT connector and the antenna terminals of a TV receiver should be made only as shown in the instructions. Failure to do so may result in operation that violates the regulations of the

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
Connections
In
order
to
watch
the
playback
picture
on
the
TV
screen
and
receive
TV
programs
on
this
VCR,
you
must
connect
the
VCR
and
the
TV
properly.
The
connection
between
the
two
units
varies
depending
upon
the
type
of
TV
and
antenna
that
you
have.
We
will
show
you
here
some
typical
ways
you
can
make
this
connection
with
the
supplied
accessories.
To
Connect
a
Cable
-TV
System
If
your
TV
has
a
built-in
CATV
decoder
CATV
75
-ohm
coaxial
cable
If
your
TV
does
not
have
a
built-in
CATV
decoder
CATV
75
-ohm
coaxial
cable
Before
You
Begin
•
Turn
off
the
power
of
the
VCR
and
TV.
•
Disconnect
the
AC
power
cord
of
the
VCR
and
TV
from
the
wall
outlet.
•
Do
not
connect
the
AC
power
cords
until
all
of
the
connections
are
completed.
Disconnect
the
CATV
cable
from
the
TV.
0
VHF/UHF
TV
UHF
VHF
CATV
cable
Disconnect
the
CATV
cable
from
the
TV.
Note
to
CATV
system
installer
in
the
U.S.A.
This
reminder
is
provided
to
call
the
cable
TV
system
installer's
attention
to
Article
£320-22
of
the
NEC
that
provides
guidelines
for
proper
grounding
and,
in
particular,
specifies
that
the
cable
ground
shall
be
connected
to
the
grounding
system
of
the
building,
as
close
to
the
point
of
cable
entry
as
practical
.
CATV
channel
converter
msesime
VHF/UHF
TV
UHF
00
CATV
channel
converter
VHF
monsium461
TV
CATV
cable
OMMINIIIIIIMININk
Caution
Connections
between
the
recorder
VHF/UHF
OUT
connector
and
the
antenna
terminals
of
a
TV
receiver
should
be
made
only
as
shown
in
the
instructions.
Failure
to
do
so
may
result
in
operation
that
violates
the
regulations
of
the
10