Sony SNC-M1 User Guide - Page 25

Wireless network Tab (SNC-M1W only), Secondary DNS server - snc m1w factory default

Get Sony SNC-M1 PDF manuals and user guides View all Sony SNC-M1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 25 highlights

Administrating the Camera Default gateway Type the default gateway. Obtain DNS server address automatically Select this to obtain the address of DNS server automatically. It can be set only when Obtain an IP address automatically (DHCP) is selected. Note When you select "Obtain DNS server address automatically", make sure that DHCP server is active on the network. Use the following DNS server address Select this when you set the fixed address as the IP address of DNS server. Primary DNS server Type the IP address of the primary DNS server. Secondary DNS server Type the IP address of the secondary DNS server, if necessary. HTTP port number Normally select 80. If you want to use a port number other than 80, select the text box and type a port number between 1024 and 65535. Note When you have set the HTTP port number to a number other than 80 on the Network setting page or in the Setup Program, access the camera by typing the IP address of the camera on the web browser, as follows: Example: when HTTP port number is set to 8000 OK/Cancel See "Buttons common to every setting menu" on page 17. Wireless network Tab (SNC-M1W only) Use this to set connection for the wireless network. SSID Type the ID to identify the wireless network you want to access using up to 32 ASCII characters (alphanumeric). For your security, be sure to change the factory setting. Type Select the network connection type Adhoc mode or Infrastructure mode. Select Adhoc mode when connecting to the computer directly, or select Infrastructure mode when connecting to the computer via an access point or a radio router. When you select Ad hoc mode, specify the wireless channel. Channel Set the channel when making adhoc connection is set up. Tip Set the channel of the computer and a camera as the sa me value. Note For better wireless communication, check for the channel used by the operating network and select the channel that is used less. WEP Select On when you use the WEP (Wired Equivalent Privacy) keys, or Off when you do not use it. The WEP key data settings are valid only when the WEP menu is set to On. WEP key data Specify up to 4 WEP keys. The length of a WEP key is 40 or 104 bit. A 104-bit WEP key has a higher security level than a 40-bit key. You can type the WEP key either in hexadecimal numbers (0 to 9 and A to F) or ASCII characters (alphanumeric). 25 Configuring the Network - Network setting Menu

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
Administrating the Camera
Configuring the Network — Network setting Menu
25
Default gateway
Type the default gateway.
Obtain DNS server address automatically
Select this to obtain the address of DNS server
automatically. It can be set only when
Obtain an IP
address automatically (DHCP)
is selected.
Note
When you select “Obtain DNS server address
automatically”, make sure that DHCP server is active on
the network.
Use the following DNS server address
Select this when you set the fixed address as the IP
address of DNS server.
Primary DNS server
Type the IP address of the primary DNS server.
Secondary DNS server
Type the IP address of the secondary DNS server, if
necessary.
HTTP port number
Normally select
80
.
If you want to use a port number
other than 80, select the text box and type a port number
between 1024 and 65535.
Note
When you have set the HTTP port number to a number
other than 80 on the Network setting page or in the Setup
Program, access the camera by typing the IP address of
the camera on the web browser, as follows:
Example: when HTTP port number is set to 8000
OK/Cancel
See “Buttons common to every setting menu” on page
17.
Wireless network Tab (SNC-M1W
only)
Use this to set connection for the wireless network.
SSID
Type the ID to identify the wireless network you want to
access using up to 32 ASCII characters (alphanumeric).
For your security, be sure to change the factory setting.
Type
Select the network connection type
Adhoc mode
or
Infrastructure mode
. Select
Adhoc mode
when
connecting to the computer directly, or select
Infrastructure mode
when connecting to the computer
via an access point or a radio router. When you select
Ad
hoc mode
, specify the wireless channel.
Channel
Set the channel when making adhoc connection is set up.
Tip
Set the channel of the computer and a camera as the sa
me value.
Note
For better wireless communication, check for the
channel used by the operating network and select the
channel that is used less.
WEP
Select
On
when you use the WEP (Wired Equivalent
Privacy) keys, or
Off
when you do not use it.
The WEP key data settings are valid only when the WEP
menu is set to
On
.
WEP key data
Specify up to 4 WEP keys.
The length of a WEP key is
40 or 104 bit.
A 104-bit WEP key has a higher security
level than a 40-bit key.
You can type the WEP key either
in hexadecimal numbers (0 to 9 and A to F) or ASCII
characters (alphanumeric).