Home » Sony Manuals » Printers » Sony UP895 » Manual Viewer

Sony UP895 Service Manual - Page 23

Electrical Alignment, 3-1. AGC Adjustment, 3-2. Video Level Adjustment

Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

Section 3 Electrical Alignment [Equipment Required] . Oscilloscope . Digital voltmeter . 10 steps signal generator Tektronix 1410 or equivalents (For NTSC signal) Tektronix 1411 or equivalents (For PAL signal) 3-1. AGC Adjustment Machine condition for adjustment . Input signal: 10 steps signal . No monitor is connected. . Set rear panel DIP switch 9 to up. (AGC-ON) Specification TP5 (AMP IN)/MA-99 (C-3) Output waveform Vs Adjustments AGC REF adjustment 1RV3/MA-99 (C-2) AGC GAIN adjustment 1RV2/MA-99 (C-2) MA-99 Procedure 1. Input a 10 steps signal and set DIP switch != to DOWN. Adjust RV3 (AGC REF) so that Vs is 700 mV. 2. Set DIP switch != to UP and adjust RV2 (AGC GAIN) so that Vs is 630 mV. . Adjust so that Vs is 700 mV when AGC is ON and 75 Z terminator is on. . Adjust so that Vs is 630 mV when AGC is ON and 75 Z terminator is off. 1RV3 1RV2 TP5 3-2. Video Level Adjustment Machine condition for adjustment Specification . Input signal: 10 steps signal . In case, monitor is not connected, set DIP switch != on the rear panel to ON, if connected, set to OFF. . Adjust RV4 (AGC OFF CONT) using 10 steps signal input. TP5 (AMP IN)/MA-99 (C-3) Output waveform 1.0 V Adjustments AGC OFF CONT adjustment 1RV4/MA-99 (C-2) MA-99 Adjust so that video signal level is 1.0 V. 1RV4 TP5 UP-895/(E) 3-1

Section	Page
Cover	1
Table of Contents	3
1.Operating Instructions	7
2.Service Information	17
2-1. Board Layout	17
2-2. Disassembly	17
2-3. Removal of Major Parts	18
2-3-1. Removal of Mechanical Block	18
2-3-2. Removal of MA-99 Board	19
2-3-3. Removal of Switching Regulator	19
2-3-4. Removal of Thermal Head	20
2-4. Tightening the Screws	21
2-5. Installation of Fan Motor	22
3.Electrical Alignment	23
3-1. AGC Adjustment	23
3-2. Video Level Adjustment	23
3-3. Brightness and Contrast Adjustment	24
3-4. Head Voltage Adjustment	25
3-5. Initialization of Print Count History	25
4.Circuit Operation Description	27
4-1. Video Circuit	29
4-1-1. BNC Input Connector - Trap Filter Circuit	29
4-1-2. nC-SYNC Generator Circuit	29
4-1-3. AGC Circuit	29
4-1-4. Brightness and Contrast Control	29
4-1-5. A/D Conversion and D/A Conversion	29
4-2. Clock Generator Circuit	30
4-3. Memory and Head Control Circuit	30
4-3-1. Reading the Serial Data from System Control	31
4-3-2. Writing in Frame Memory	31
4-3-3. Transfer from Frame Memory to Line Memory	31
4-3-4. Thermal Head Control and One-Line Memory	31
4-4. System Control Section	34
4-4-1. Reading of Keys	34
4-4-2. Reading of Function Switches	34
4-4-3. Platen Motor Control	35
4-4-4. Head Up and Down Control	36
4-4-5. Monitor of Door Sensor	36
4-4-6. Monitor of Paper Sensor	36
4-4-7. Monitor of Head Temperature Sensor	37
4-4-8. Control of Head Fan Motor (for Head Cooling)	37
4-4-9. Control of Video Circuit Section	37
4-4-10. Control of Memory and Head Control Circuit	38
4-4-11. Gamma Correction and Thermal Storage Correction	39
4-4-12. Discrimination of Video Signal to be Input	39
4-4-13. Remote Interface	39
4-4-14. Storage of Print Count History	39
4-5. Thermal Head Section	40
4-5-1. Structure	40
4-5-2. Basic Operation	41
4-5-3. Stair Generation	41
4-5-4. Temperature Correction	42
4-5-5. Line Count Correction	42
5.Troubleshooting	43
5-1. Print is Faulty	43
5-2. Print is Too Dark or Too Light	44
5-3. “Paper Sensor” is Out of Order	45
5-4. Head Operation (Up & Down) is Out of Order	46
5-5. Paper Feeding is Out of Order	47
5-6. Door (Opening and Closing) is Out of Order	48
6.Service Mode (Self-diagnostic Function)	49
6-1 Printing the Test Pattern	49
6-2. Up/Down Operation of Head	50
6-3. Feed Operation	50
6-4. Display and Clearing of Print Sheet History	51
7.Semiconductor Pin Assignments	53
8.Spare Parts	55
8-1. Notes on Repair Parts	55
8-2. Exploded Views	56
8-3. Electrical Parts List	61
9.Block Diagram	69
Overall	69
10.Schematic Diagrams and Board Layouts	71
Frame	72
KY-454	73
SE-531	73
SE-532	73
SU-52	73