Home » Sony Manuals » Printers » Sony UP895 » Manual Viewer

Sony UP895 Service Manual - Page 49

Service Mode (Self-diagnostic Function), 6-1 Printing the Test Pattern

Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

Section 6 Service Mode (Self-diagnostic Function) Turn on the power while pressing and holding the PRINT and COPY keys. Release the keys when the buzzer sounds after about two seconds. The service mode is then entered. 6-1 Printing the Test Pattern Set the POSI/ENGA switch to POSI (no print can be performed when this switch is set to NEGA). "Stair step" and "Gray" are available as a test pattern for printing. 1 Press the PRINT key. → Print the stair step pattern. 2 Press the COPY key. → Print the gray pattern. For the gray pattern, the concentration of gray can be selected from 100 % white to 100 % black in five steps using the PRINT SIZE switch. 100 % white Intermediate gray 100 % black UP-895/(E) Stair step Gray 6-1

Section	Page
Cover	1
Table of Contents	3
1.Operating Instructions	7
2.Service Information	17
2-1. Board Layout	17
2-2. Disassembly	17
2-3. Removal of Major Parts	18
2-3-1. Removal of Mechanical Block	18
2-3-2. Removal of MA-99 Board	19
2-3-3. Removal of Switching Regulator	19
2-3-4. Removal of Thermal Head	20
2-4. Tightening the Screws	21
2-5. Installation of Fan Motor	22
3.Electrical Alignment	23
3-1. AGC Adjustment	23
3-2. Video Level Adjustment	23
3-3. Brightness and Contrast Adjustment	24
3-4. Head Voltage Adjustment	25
3-5. Initialization of Print Count History	25
4.Circuit Operation Description	27
4-1. Video Circuit	29
4-1-1. BNC Input Connector - Trap Filter Circuit	29
4-1-2. nC-SYNC Generator Circuit	29
4-1-3. AGC Circuit	29
4-1-4. Brightness and Contrast Control	29
4-1-5. A/D Conversion and D/A Conversion	29
4-2. Clock Generator Circuit	30
4-3. Memory and Head Control Circuit	30
4-3-1. Reading the Serial Data from System Control	31
4-3-2. Writing in Frame Memory	31
4-3-3. Transfer from Frame Memory to Line Memory	31
4-3-4. Thermal Head Control and One-Line Memory	31
4-4. System Control Section	34
4-4-1. Reading of Keys	34
4-4-2. Reading of Function Switches	34
4-4-3. Platen Motor Control	35
4-4-4. Head Up and Down Control	36
4-4-5. Monitor of Door Sensor	36
4-4-6. Monitor of Paper Sensor	36
4-4-7. Monitor of Head Temperature Sensor	37
4-4-8. Control of Head Fan Motor (for Head Cooling)	37
4-4-9. Control of Video Circuit Section	37
4-4-10. Control of Memory and Head Control Circuit	38
4-4-11. Gamma Correction and Thermal Storage Correction	39
4-4-12. Discrimination of Video Signal to be Input	39
4-4-13. Remote Interface	39
4-4-14. Storage of Print Count History	39
4-5. Thermal Head Section	40
4-5-1. Structure	40
4-5-2. Basic Operation	41
4-5-3. Stair Generation	41
4-5-4. Temperature Correction	42
4-5-5. Line Count Correction	42
5.Troubleshooting	43
5-1. Print is Faulty	43
5-2. Print is Too Dark or Too Light	44
5-3. “Paper Sensor” is Out of Order	45
5-4. Head Operation (Up & Down) is Out of Order	46
5-5. Paper Feeding is Out of Order	47
5-6. Door (Opening and Closing) is Out of Order	48
6.Service Mode (Self-diagnostic Function)	49
6-1 Printing the Test Pattern	49
6-2. Up/Down Operation of Head	50
6-3. Feed Operation	50
6-4. Display and Clearing of Print Sheet History	51
7.Semiconductor Pin Assignments	53
8.Spare Parts	55
8-1. Notes on Repair Parts	55
8-2. Exploded Views	56
8-3. Electrical Parts List	61
9.Block Diagram	69
Overall	69
10.Schematic Diagrams and Board Layouts	71
Frame	72
KY-454	73
SE-531	73
SE-532	73
SU-52	73