Sony UPDR200 Operating Instructions - Page 10

To load the paper roll, Paper with 127-mm 5-inch width: 2UPC-R203 - ink

Page 10 highlights

Operation Note If you use the 2UPC-R204 series or 2UPC-R206 series Printing Pack with the 152-mm (6-inch) paper width after using the 2UPC-R203 series or 2UPC-R205 series Printing Pack with the 127-mm (5-inch) paper width, white stripes may appear on either side of printouts. Be sure to clean the inside of the printer before printing (page 24). To load the paper roll Notes • Be sure to remove the output tray and the scrap receptacle before loading the paper roll. • Be careful that your fingers and clothing are not caught in the paper door or on the protuberance in the opening of the door. 1 Press and lower the paper door lever, hold the paper door at the center portion, and pull the door forward until it locks into the open position. 3 Insert the paper core into the paper roll. The two sides of the paper core are the same shape. You can insert either side. Notes • If the edges of the paper on the roll are not aligned before inserting the paper core, be sure to align them while being careful not to bend or damage them. Not doing so may result in malfunction. • If the leading edge of the paper is bent or damaged as a result of a paper jam, for example, be sure to use scissors to cut off the damaged portion, as shown, before inserting the paper. 2 Remove the paper core from the printer. • Do not bump the paper roll against hard objects or squeeze it tightly. Doing so may bend or crease the paper and affect print quality. 4 Depending on the width of your paper roll, attach or remove the paper adapters. Paper with 127-mm (5-inch) width: 2UPC-R203 series and 2UPC-R205 series Printing Pack Attach the blue paper adapter to the left side of the printer, and the pink paper adapter to the right side. 10 Loading the Paper Roll and Ink Ribbon

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31

Operation
Loading the Paper Roll and Ink Ribbon
10
Note
If you use the 2UPC-R204 series or 2UPC-R206 series
Printing Pack with the 152-mm (6-inch) paper width
after using the 2UPC-R203 series or 2UPC-R205 series
Printing Pack with the 127-mm (5-inch) paper width,
white stripes may appear on either side of printouts.
Be sure to clean the inside of the printer before printing
(page 24).
To load the paper roll
Notes
Be sure to remove the output tray and the scrap
receptacle before loading the paper roll.
Be careful that your fingers and clothing are not
caught in the paper door or on the protuberance in the
opening of the door.
1
Press and lower the paper door lever, hold the paper
door at the center portion, and pull the door forward
until it locks into the open position.
2
Remove the paper core from the printer.
3
Insert the paper core into the paper roll.
The two sides of the paper core are the same shape.
You can insert either side.
Notes
If the edges of the paper on the roll are not aligned
before inserting the paper core, be sure to align
them while being careful not to bend or damage
them. Not doing so may result in malfunction.
If the leading edge of the paper is bent or
damaged as a result of a paper jam, for example,
be sure to use scissors to cut off the damaged
portion, as shown, before inserting the paper.
Do not bump the paper roll against hard objects or
squeeze it tightly. Doing so may bend or crease
the paper and affect print quality.
4
Depending on the width of your paper roll, attach or
remove the paper adapters.
Paper with 127-mm (5-inch) width: 2UPC-R203
series and 2UPC-R205 series Printing Pack
Attach the blue paper adapter to the left side of the
printer, and the pink paper adapter to the right side.