Sony ZRD-2 Operating Instructions - Page 14

Displaying 3D Video

Get Sony ZRD-2 PDF manuals and user guides View all Sony ZRD-2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

Caution [AdobeRGB], [DCI], and [BT.2020] do not include the entirety of the color spaces defined by their respective standards. [Light Output] (version 1.20.0 or later only): Select the output strength to use during low lightsource output. For details, refer to the Installation Manual. • [Full]: Output at 100% strength. • [High]: Output at 75% strength. • [Medium]: Output at 50% strength. • [Low]: Output at 25% strength. Caution The [Light Output] setting will be disabled if [HDR] is set to a setting other than [Off] (version 1.20.0 through 1.21.1). [Color Temperature Settings]: Select the color temperature in [Color Temperature]. • If you selected [D93], [D65], [D50] or [DCI] (ZRCT-200 version 1.22.0 or later), proceed to step 4 . • If you selected [D93 Custom (Offset)], [D65 Custom (Offset)], or [D50 Custom (Offset)], [DCI Custom (Offset)] (ZRCT-200 version 1.22.0 or later), proceed to step 3 . 3 Configure the offset values. These settings can only be configured when [Color Temperature Settings] is set to "Custom (Offset)" in step 2 . Use the slider and buttons to adjust the contrast. Setting range: -128 to +127 Default value: 0 4 When you are finished configuring settings, click [Close]. Displaying 3D Video Note In this document, the signals for the left and right eyes are referred to as the L and R signals respectively. For details, refer to the Installation Manual. Caution 3D video display is not supported for HDMI signals. 3D frame sequential mode: This mode alternately inputs the two video signals (L signal and R signal) to the DisplayPort connector and outputs the 3D image from the display unit. Generated 3D sync signals based on 3D sync signal inputs from the 3D SYNC IN connector are output from the 3D SYNC OUT connector according to the picture output's timing. 3D dual input mode: This mode simultaneously inputs the two video signals (L signal and R signal) to the DisplayPort connector or the DVI connector, and the 3D image is output from the display unit. Internally generated 3D sync signals are output from the 3D SYNC OUT connector according to the picture output's timing. Select [3D Settings] in the [Array] menu on the main screen of Display Control Software to display the [3D Settings] screen. Before version 1.22.0 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
14
Caution
[AdobeRGB], [DCI], and [BT.2020] do not
include the entirety of the color spaces defined by
their respective standards.
[Light Output] (version 1.20.0 or later only):
Select the output strength to use during low light-
source output. For details, refer to the Installation
Manual.
•
[Full]: Output at 100% strength.
•
[High]: Output at 75% strength.
•
[Medium]: Output at 50% strength.
•
[Low]: Output at 25% strength.
Caution
The [Light Output] setting will be disabled if
[HDR] is set to a setting other than [Off] (version
1.20.0 through 1.21.1).
[Color Temperature Settings]:
Select the color
temperature in [Color Temperature].
•
If you selected [D93], [D65], [D50] or [DCI]
(ZRCT-200 version 1.22.0 or later), proceed to
step
4
.
•
If you selected [D93 Custom (Offset)], [D65
Custom (Offset)], or [D50 Custom (Offset)],
[DCI Custom (Offset)] (ZRCT-200 version
1.22.0 or later), proceed to step
3
.
3
Configure the offset values.
These settings can only be configured when [Color
Temperature Settings] is set to “Custom (Offset)” in
step
2
.
Use the slider and
buttons to adjust the contrast.
Setting range: –128 to +127
Default value: 0
4
When you are finished configuring settings, click
[Close].
Displaying 3D Video
Note
In this document, the signals for the left and right eyes are
referred to as the L and R signals respectively.
For details, refer to the Installation Manual.
Caution
3D video display is not supported for HDMI signals.
3D frame sequential mode:
This mode alternately inputs the two video signals (L
signal and R signal) to the DisplayPort connector and
outputs the 3D image from the display unit.
Generated 3D sync signals based on 3D sync signal inputs
from the 3D SYNC IN connector are output from the 3D
SYNC OUT connector according to the picture output’s
timing.
3D dual input mode:
This mode simultaneously inputs the two video signals (L
signal and R signal) to the DisplayPort connector or the
DVI connector, and the 3D image is output from the
display unit.
Internally generated 3D sync signals are output from the
3D SYNC OUT connector according to the picture
output’s timing.
Select [3D Settings] in the [Array] menu on the main
screen of Display Control Software to display the [3D
Settings] screen.
Before version 1.22.0