Stihl HT 101 Instruction Manual - Page 30

Throttle Cable. - carburetor

Get Stihl HT 101 PDF manuals and user guides View all Stihl HT 101 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

English N Do not let the starter grip snap back. Guide it slowly back into the housing so that the starter rope can rewind properly. N Crank the engine until it begins to fire. After no more than five attempts, turn the choke knob to e. N Continue cranking. As soon as the engine runs N Blip the throttle trigger. The slide control moves to the normal run position F - and the engine settles down to idle speed. WARNING Make sure the carburetor is correctly adjusted. The saw chain must not rotate when the engine is idling. Your machine is now ready for operation. Stopping the engine N Push the slide control in the direction of the arrow on the stop symbol (h) to STOP-0. At very low outside temperatures As soon as the engine runs: N Blip the throttle trigger to disengage the starting throttle position. The slide control moves to the normal run F - and the engine settles down to idle speed. N Open the throttle slightly. N Warm up the engine for a short period. If engine does not start Choke knob If you did not turn the choke knob to e quickly enough after the engine began to fire, the combustion chamber is flooded. N Turn the choke knob to e. N Set the slide control, lockout lever and throttle trigger to the starting throttle position. N Start the engine by pulling the starter rope briskly - 10 to 20 pulls may be necessary. If the engine still does not start N Move the slide control to STOP-0. N Remove the spark plug - see "Spark Plug". N Dry the spark plug. N Crank the engine several times with the starter to clear the combustion chamber. N Refit the spark plug - see "Spark Plug". N Move the slide control to START. N Set the choke knob to e - even if the engine is cold. N Now start the engine. Throttle cable adjustment N Check adjustment of throttle cable - see chapter on "Adjusting the Throttle Cable". Fuel tank run until completely dry N After refueling, press the manual fuel pump bulb at least five times - even if the bulb is filled with fuel. N Set the choke knob according to engine temperature. N Start the engine. 28 HT 100, HT 101, HT 130, HT 131

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
HT 100, HT 101, HT 130, HT 131
English
28
N
Do not let the starter grip snap back.
Guide it slowly back into the housing
so that the starter rope can rewind
properly.
N
Crank the engine until it begins to
fire. After no more than
five
attempts
, turn the choke knob to
e
.
N
Continue cranking.
As soon as the engine runs
N
Blip the throttle trigger. The slide
control moves to the normal run
position
F
– and the engine settles
down to idle speed.
WARNING
Make sure the carburetor is correctly
adjusted. The saw chain must not rotate
when the engine is idling.
Your machine is now ready for
operation.
Stopping the engine
N
Push the slide control in the
direction of the arrow on the stop
symbol (
h
) to
STOP
-
0
.
At very low outside temperatures
As soon as the engine runs:
N
Blip the throttle trigger to disengage
the
starting throttle position
. The
slide control moves to the normal
run
F
– and the engine settles down
to idle speed.
N
Open the throttle slightly.
N
Warm up the engine for a short
period.
If engine does not start
Choke knob
If you did not turn the choke knob to
e
quickly enough after the engine began to
fire, the combustion chamber is flooded.
N
Turn the choke knob to
e
.
N
Set the slide control, lockout lever
and throttle trigger to the
starting
throttle position
.
N
Start the engine by pulling the
starter rope briskly – 10 to 20 pulls
may be necessary.
If the engine still does not start
N
Move the slide control to
STOP
-
0
.
N
Remove the spark plug – see
"Spark Plug".
N
Dry the spark plug.
N
Crank the engine several times with
the starter to clear the combustion
chamber.
N
Refit the spark plug – see "Spark
Plug".
N
Move the slide control to
START
.
N
Set the choke knob to
e
– even if
the engine is cold.
N
Now start the engine.
Throttle cable adjustment
N
Check adjustment of throttle cable –
see chapter on "Adjusting the
Throttle Cable".
Fuel tank run until completely dry
N
After refueling, press the manual
fuel pump bulb at least five times –
even if the bulb is filled with fuel.
N
Set the choke knob according to
engine temperature.
N
Start the engine.