TASCAM Celesonic US-20x20 Reference Manual - Page 21

Interface

Get TASCAM Celesonic US-20x20 PDF manuals and user guides View all TASCAM Celesonic US-20x20 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 21 highlights

6 - Using the Settings Panel INTERFACE page 88 Windows Status display area Setting area Windows "INTERFACE" page in AUDIO I/F mode Status display area Setting area Mac "INTERFACE" page in AUDIO I/F mode The "INTERFACE" page is divided into two areas. One shows the status of the unit and the other shows settings. An image of the rear panel of the unit is shown at the bottom of the page so you can check the layout of connectors, for example. (No setting changes or other operations are possible using this image.) Status display area This shows the current status of the unit. Item displayed Software Version Firmware Version Device Clock Source Sample Rate Digital Input Status Meaning Version of the software being used Version of the firmware used by the unit Unit model Name of the currently selected clock source Current sampling frequency Current status of digital input Depending on the status of the digital input, the following will appear for the Digital Input Statusitem. Item displayed Lock Meaning A valid digital signal is being input. Unlock No valid digital signal is being detected. NOTE • ("No Device" is shown for the "Firmware Version" and "Device" items when the unit and the computer are not connected.) • "No ASIO Driver" is show for the "Sample Rate" item if no ASIO driver has been installed. Setting area 1 Sample Clock Source Use this to set the sampling clock source. Options: COAXIAL The clock signal input through the COAXIAL IN connector is used. OPTICAL(TASCAM Auto Mode) The clock signal input through the OPTICAL IN connector is used. If the connected device is a TASCAM device, the input clock signal will be automatically identified and set. OPTICAL(44.1kHz/48kHz/88.2kHz/96kHz) The clock signal input through the OPTICAL IN connector is used. Use this setting if the connected device is not a TASCAM device and the input clock signal is 44.1, 48, 88.2 or 96 kHz. OPTICAL(176.4kHz/192kHz) The clock signal input through the OPTICAL IN connector is used. Use this setting if the connected device is not a TASCAM device and the input clock signal is 176.4 or 192 kHz. WORD The clock signal input through the WORD IN connector is used. INTERNAL The unit's built-in clock is always used. NOTE • When set to COAXIAL, OPTICAL or WORD, if no signal is input through the corresponding connector or synchroni- TASCAM US-20x20 21

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
TASCAM
US-20x20
21
6 – Using the Settings Panel
INTERFACE page
8
Windows
Status display area
Setting area
Windows “INTERFACE” page in AUDIO I/F mode
Status display area
Setting area
Mac “INTERFACE” page in AUDIO I/F mode
The “INTERFACE” page is divided into two areas. One shows the
status of the unit and the other shows settings.
An image of the rear panel of the unit is shown at the bottom
of the page so you can check the layout of connectors, for
example. (No setting changes or other operations are possible
using this image.)
Status display area
This shows the current status of the unit.
Item displayed
Meaning
Software Version
Version of the software being used
Firmware Version
Version of the firmware used by
the unit
Device
Unit model
Clock Source
Name of the currently selected
clock source
Sample Rate
Current sampling frequency
Digital Input Status
Current status of digital input
Depending on the status of the digital input, the following will
appear for the Digital Input Statusitem.
Item
displayed
Meaning
Lock
A valid digital signal is being input.
Unlock
No valid digital signal is being detected.
NOTE
•
("No Device” is shown for the “Firmware Version” and
“Device” items when the unit and the computer are not
connected.)
•
"No ASIO Driver” is show for the “Sample Rate” item if no
ASIO driver has been installed.
Setting area
1
Sample Clock Source
Use this to set the sampling clock source.
Options:
COAXIAL
The clock signal input through the
COAXIAL IN
connector is used.
OPTICAL(TASCAM Auto Mode)
The clock signal input through the
OPTICAL IN
connector is used.
If the connected device is a TASCAM device, the input
clock signal will be automatically identified and set.
OPTICAL(44.1kHz/48kHz/88.2kHz/96kHz)
The clock signal input through the
OPTICAL IN
connector is used.
Use this setting if the connected device is not a
TASCAM device and the input clock signal is 44.1, 48,
88.2 or 96 kHz.
OPTICAL(176.4kHz/192kHz)
The clock signal input through the
OPTICAL IN
connector is used.
Use this setting if the connected device is not a
TASCAM device and the input clock signal is 176.4 or
192 kHz.
WORD
The clock signal input through the
WORD IN
connector
is used.
INTERNAL
The unit's built-in clock is always used.
NOTE
•
When set to COAXIAL, OPTICAL or WORD, if no signal is
input through the corresponding connector or synchroni-