Home » TP-Link Manuals » Hubs & Switches » TP-Link TL-SL3428 » Manual Viewer

TP-Link TL-SL3428 User Guide - Page 47

The procedures called from the Startup menu cover software download, ﬂash

UPC - 845973020491

Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

TL-SG3109/TL-SL3428/TL-SL3452 Gigabit Managed Switch Family Installation Guide The procedures called from the Startup menu cover software download, flash handling, and password recovery. The diagnostics procedures are for use by technical support personnel only and are not disclosed in this document. The Startup menu can be entered when booting the device. A user input must be entered immediately after the POST test. To enter the Startup menu: 1. Turn the power on and watch for the auto-boot message. ------ Performing the Power-On Self Test (POST) -----UART Channel Loopback Test PASS Testing the System SDRAM PASS Boot1 Checksum Test PASS Boot2 Checksum Test PASS Flash Image Validation Test PASS BOOT Software Version 1.0.0.04 Built 29-Nov-2005 11:56:12 TPLink Switch based on 88E6218 with ARM946E-S. 32MByte SDRAM. I-Cache 8 KB. D-Cache 8 KB. Cache Enabled. Autoboot in 2 seconds - press RETURN or Esc. to abort and enter prom. 2. When the auto-boot message appears, press to display the Startup menu. 40

Section	Page
Package contents	8
Section 1: Introduction	9
1.1 Intended Audience	9
1.2 Agreement	9
1.3 Guide Overview	9
Section 2. Device Description	10
2.1 Features	10
2.2 TP-Link TL-SG3109 Description	11
2.3 TP-Link TL-SL3428 Description	13
2.4 TP-Link TL-SL3452 Description	15
2.5 Back Panel	17
2.6 Device Hardware Interfaces	17
2.6.1 RJ-45 Base-T Fast Ethernet Ports	17
2.6.2 SFP Port	18
2.6.3 RS-232 DB-9 Console Port	19
2.7 Cable, Port, and Pinout Information	19
2.7.1 Pin Explain For RJ-45 Connector	19
2.7.2 SFP Connector	21
2.8 Physical Dimensions	21
Section 3. Mounting Device	22
3.1 Preparing for Installation	22
3.1.1 Installation Precautions	22
3.1.2 Site Requirements	23
3.1.3 Unpacking	23
3.1.3.1 Package Contents	23
3.1.3.2 Unpacking Essentials	24
3.2 Installing the Device	24
3.2.1 Desktop or Shelf Installation	25
3.2.2 Rack Installation	25
3.3 Connecting the Device	27
3.3.1 Connecting the Switch to a Terminal	27
3.3.2 AC Power Connection	28
Section 4. Starting and Configuring the Device	29
4.1 Configuring the Terminal	29
4.2 Installation Procedure	30
4.2.1 Device Port Default Settings	31
4.3 Booting the Device	31
4.4 Configuration Overview	33
4.4.1 Initial Configuration	34
4.4.1.1 Static IP Address and Subnet Mask	35
4.4.1.2 Assigning Static IP Addresses on a default VLAN	36
4.4.1.3 User Name	37
4.4.1.4 SNMP Community Strings	38
4.5 Advanced Configuration	40
4.5.1 Receiving an IP Address from a DHCP Server	41
4.5.2 Receiving an IP Address from a BOOTP Server	42
4.5.3 Security Management and Password Configuration	43
4.5.3.1 Configuring Security Passwords Introduction	44
4.5.3.2 Configuring an Initial Console Password	44
4.5.3.3 Configuring an Initial Telnet Password	45
4.5.3.4 Configuring an Initial SSH password	45
4.5.3.5 Configuring an Initial HTTP Password	46
4.5.3.6 Configuring an initial HTTPS Password	46
4.6 Startup Procedures	46
4.6.1 Software Download [Option 1]	48
4.6.1.1 Software Download through TFTP Server	49
4.6.2 Erasing the Flash File [Option 2]	53
4.6.3 Password Recovery [Option 3]	53
4.6.4 Enter Diagnostic Mode [Option4]	54