TP-Link TL-WPS510U User Guide - Page 30

Internet Protocol TCP/IP Properties, Network Type/ SSID /Channel

Get TP-Link TL-WPS510U PDF manuals and user guides
UPC - 845973031039
View all TP-Link TL-WPS510U manuals
Add to My Manuals
Save this manual to your list of manuals

Page 30 highlights

TL-WPS510U Pocket-Sized Wireless N Print Server 14. Enter the "Internet Protocol (TCP/IP) Properties" page as shown in Figure 3-31. Fill in the following parameters. ¾ IP Address: Specify an IP address for your adapter. The IP address must be within the same subnet as your wireless router or access point. For example, if the LAN IP address of your wireless router or access point is 192.168.1.1, the IP address should be set to 192.168.1.X (1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
TL-WPS510U
Pocket-Sized Wireless N Print Server
14. Enter the “
Internet Protocol (TCP/IP) Properties
” page as shown in Figure 3-31. Fill in the
following parameters.
¾
IP Address:
Specify an IP address for your adapter. The IP address must be within the
same subnet as your wireless router or access point. For example, if the LAN IP address
of your wireless router or access point is
192.168.1.1
, the IP address should be set to
192.168.1.X
(1<X<10 or 10<X255, for 192.168.1.10 has been specified for your print
server). Here we take 192.168.1.101 for example.
¾
Subnet Mask:
Enter the subnet mask of your network.
¾
Default Gateway:
Enter the LAN IP address of your wireless router or access point. Here
takes 192.168.1.1 for example.
Figure 3-31
15. Log into the web management page of the print server again. Select “
Setup
”, and then
choose “
Wireless
”. Configure the following wireless parameters.
¾
Network Type/ SSID /Channel:
select the network (Take TP-LINK_A4161E for example)
from the “
Site Survey
” list and then these three fields will be automatically filled.
¾
Transmission Rate:
Keep the default value.
¾
Wireless Mode:
Keep the default value.
¾
Security Type:
Select the security type of your wireless router (TP-LINK_A4161E) and
then enter the key. Here we take WPA-PAK security type with 1234567890 as the key for
example.
23