TP-Link Touch P5 Touch P5 V1 User Guide - Page 49

Access the USB disk, Enable Authentication for Data Security

Get TP-Link Touch P5 PDF manuals and user guides View all TP-Link Touch P5 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 49 highlights

• Get a safe backup for the materials for a presentation. • Remove the files on your camera's memory card from time to time during the journey. Note: If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), you cannot use this feature because private addresses are not routed on the Internet. 1. Access the USB disk 1 ) Connect Your USB Disk Insert your USB storage device into your Touch P5's USB port directly or using a USB cable. Wait several seconds until the USB LED becomes solid on. Note: • If you use USB hubs, make sure no more than four devices are connected to your Touch P5. • If the USB storage device requires using bundled external power, make sure the external power has been connected. • If you use a USB hard drive, make sure its file system is FAT32 or NTFS. • Before you physically disconnect a USB device from your Touch P5, safely remove it to avoid data damage: Select Advanced > USB Settings > Device Settings and click . 2 ) Enable Authentication for Data Security It is strongly recommended that you set and apply a sharing account for data security. a . Visit http://tplinkwifi.net/, then log in with the username and password you set for your Touch P5. b . Select Advanced > USB Settings > Sharing Access. c . Choose to use the default Account (admin) or use a new account and click Save. d . Enable Authentication to apply the sharing account. • If you leave Share All enabled, click the button to enable Authentication for all folders. • If Share All is disabled, enable Authentication for specific folders. 3 ) Enable the FTP(via Internet) Tick the check box to enable FTP(Via Internet), then click Save. Chapter 2 . Configure Touch P5 as a Router 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
46
Chapter 2 .
Configure Touch P5 as a Router
•
Get a safe backup for the materials for a presentation.
•
Remove the files on your camera’s memory card from time to time during the journey.
Note:
If your ISP assigns a private WAN IP address (such as 192.168.x.x or 10.x.x.x), you cannot use this feature because private
addresses are not routed on the Internet.
1.
Access the USB disk
1 )
Connect Your USB Disk
Insert your USB storage device into your Touch P5’s USB port directly or using a USB cable. Wait several seconds until
the USB LED becomes solid on.
Note:
•
If you use USB hubs, make sure no more than four devices are connected to your Touch P5.
• If the USB storage device requires using bundled external power, make sure the external power has been
connected.
•
If you use a USB hard drive, make sure its file system is FAT32 or NTFS.
•
Before you physically disconnect a USB device from your Touch P5, safely remove it to avoid data damage: Select
Advanced
>
USB Settings
>
Device Settings
and click
.
2 )
Enable Authentication for Data Security
It is strongly recommended that you set and apply a sharing account for data security.
a .
Visit
http://tplinkwifi.net/
, then log in with the username and password you set for your Touch P5.
b .
Select
Advanced
>
USB Settings
>
Sharing Access
.
c .
Choose to use the default Account (admin) or use a new account and click Save.
d .
Enable
Authentication
to apply the sharing account.
• If you leave
Share All
enabled, click the button to enable
Authentication
for all folders.
• If
Share All
is disabled, enable
Authentication
for specific folders.
3 )
Enable the FTP(via Internet)
Tick the check box to enable
FTP(Via Internet)
, then click
Save
.