Thermador MED301WS Instruction manual - Page 39

Maximum Operating Time Exceeded, Oven Light

Page 39 highlights

Oven door closes faster/slower than normal. The appliance cannot be switched on or is on and cannot be operated; the , symbol is shown on the display. The appliance does not heat up; 6 is shown on the display. The soft-close door hinges contain a damping fluid that is affected by temperature. If the oven is in a cold environment, the door will close slower than it will in a warmer environment. A warmer than normal environment, such as when cooking, may cause the door to close slightly faster. The panel lock is activated. Press and hold the LOCK touch button (or TIMERS, if LOCK is not present) until the , symbol goes away. Demo mode is activated in the basic settings. Turn demo mode to OFF in the settings menu. Maximum Operating Time Exceeded Your appliance automatically ends the operation if no duration has been set and the setting has not been changed for 24 hours. The actual cooking time until the operation is stopped automatically varies according to the selected settings. A message appears on the display on the appliance to say that the operation is being ended automatically. Afterwards, the operation is stopped. To use the appliance again, first switch it off. To switch the appliance back on set the required operation. 3. Remove oven rack to provide access to the bulb housing. Oven Light To replace the halogen bulb on the oven sidewall: Tools required èɊȯ PP Narrow flat blade screwdriver (blade tip width 1/ 5" (5 mm) or less to fit in slot). 4. Remove screw from top of bulb housing. 5. Insert the tip of a narrow flat blade screwdriver between the metal clips at about a 40° angle. The screwdriver blade must be able to pass between the metal clips to reach the inner catch. Flashlight (to see socket holes to plug in bulb prongs). G-9 Halogen bulb 1. Turn off power to the oven at the main power supply (fuse or breaker box). 2. Remove three screws from oven cavity holding the rack in place. 39

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92

39
Maximum Operating Time Exceeded
Your appliance automatically ends the operation if no
duration has been set and the setting has not been
changed for 24 hours.
The actual cooking time until the operation is stopped
automatically varies according to the selected settings.
A message appears on the display on the appliance to
say that the operation is being ended automatically.
Afterwards, the operation is stopped.
To use the appliance again, first switch it off. To switch
the appliance back on set the required operation.
Oven Light
To replace the halogen bulb on the oven sidewall:
1.
Turn off power to the oven at the main power supply
(fuse or breaker box).
2.
Remove three screws from oven cavity holding the
rack in place.
3.
Remove oven rack to provide access to the bulb
housing.
4.
Remove screw from top of bulb housing.
5.
Insert the tip of a narrow flat blade screwdriver
between the metal clips at about a 40° angle. The
screwdriver blade must be able to pass between the
metal clips to reach the inner catch.
Oven door closes faster/slower than normal.
The soft-close door hinges contain a damping fluid that is
affected by temperature. If the oven is in a cold environment,
the door will close slower than it will in a warmer
environment. A warmer than normal environment, such as
when cooking, may cause the door to close slightly faster.
The appliance cannot be switched on or is on and
cannot be operated; the
symbol is shown on the
display.
The panel lock is activated. Press and hold the LOCK touch
button (or TIMERS, if LOCK is not present) until the
symbol goes away.
The appliance does not heat up;
6
is shown on the
display.
Demo mode is activated in the basic settings. Turn demo
mode to OFF in the settings menu.
Tools required
Narrow flat blade screw-
driver (blade tip width 1/
5" (5 mm) or less to fit in
slot).
Flashlight (to see socket
holes to plug in bulb
prongs).
G-9 Halogen bulb