Home » Thermador Manuals » Ovens » Thermador MEDMCW31JP » Manual Viewer

Thermador MEDMCW31JP User Manual - Page 26

Maintenance

View all Thermador MEDMCW31JP manuals

Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

Part Painted Surfaces Porcelain Surfaces Stainless Steel Surfaces Plastic & Controls Probe Printed areas (words & numbers) Recommendations Clean with hot soapy water or apply Fantastik® or Formula 409® to a clean sponge or paper towel and wipe clean. Avoid using powder cleaning agents, steel wool pads and oven cleaners. Immediately wipe up acid spills like fruit juice, milk and tomatoes with a dry cloth. Do not use a moistened sponge/cloth on hot porcelain. When cool, clean with hot soapy water or apply BonAmi® or Soft Scrub® to a damp sponge. Rinse and dry. For stubborn stains, use soap-filled pads. It is normal for porcelain to show fine lines with age due to exposure to heat and food soil. Always wipe or rub in the direction of the grain. Clean with a soapy sponge, then rinse and dry, or wipe with Fantastik® or Formula 409® sprayed on a paper towel. Protect and polish with Stainless Steel Magic® and a soft cloth. Remove water spots with a cloth dampened with white vinegar. Use Bar Keeper´s Friend® to remove heat discoloration. When cool, clean with soapy water, rinse and dry. Wipe with soapy water. Do not submerge. Do not wash in the dishwasher. Do not use abrasive cleaners or petroleum based solvents. Maintenance Replacing an Oven Light 9 CAUTION WHEN REPLACING AN OVEN LIGHT: ▯ Make sure the appliance and lights are cool and power to the appliance has been turned off before replacing the light bulb(s). Failure to do so could result in electrical shock or burns. ▯ The lenses must be in place when using the appliance. ▯ The lenses serve to protect the light bulb from breaking. ▯ The lenses are made of glass. Handle carefully to avoid breaking. Broken glass could cause an injury. ▯ Light socket is live when door is open. Use only 120 volt, 25 watt halogen light bulbs, G9 base. These bulbs can be purchased through retail stores. Use a clean, dry cloth to handle halogen light bulbs. This will increase the life of the bulb. Hint: Some users may find it helpful to remove the oven door to provide easier access and visibility. See the following section: "Removing the oven door". To replace the halogen bulb on the oven ceiling: 1. Turn off power to the oven at the main power supply (fuse or breaker box). 2. Remove the oven racks if necessary to provide access to the bulb housing. 3. Remove the glass cover by unscrewing it. 4. The halogen bulb is visible in the light fixture. 5. Remove the halogen bulb by pulling it out of the 2 pin socket. Pull straight down and out. 26

Section	Page
masterpiece® series built-in oven	1
Table of Contents 4	3
Table of ContentsUse and care manual	4
About This Manual	5
How This Manual is Organized	5
Signal Words for Safety and Best Use	5
9 WARNING	5
9 CAUTION	5
NOTICE:	5
Note:	5
IMPORTANT SAFETY INSTRUCTIONS	6
READ AND SAVE THESE INSTRUCTIONS	6
WARNING	6
Proper Installation and Maintenance	6
WARNING	6
WARNING	6
WARNING	6
WARNING	6
Fire Safety	6
WARNING	6
WARNING	6
WARNING	7
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A GREASE FIRE, OBSERVE THE FOLLOWING:	7
a. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.	7
b. NEVER PICK UP A FLAMING PAN – You may be burned.	7
c. DO NOT USE WATER, including wet dishcloths or towels – a violent steam explosion will result.	7
d. Use an extinguisher ONLY if:	7
Burn Prevention	7
CAUTION	7
Child Safety	7
CAUTION	7
Cleaning Safety	8
Cookware Safety	8
NOTICE:	8
Getting Started	9
Parts	9
Cooling Fan	9
Oven Vent	9
Convection Fan	9
Oven Bottom	10
9 WARNING	10
Accessories	10
Inserting Racks	10
9 CAUTION	10
Flat Rack	10
1. Grasp rack firmly on both sides.	10
2. Insert rack (see picture).	10
3. Tilt rack up to allow stop into rack guide.	10
4. Bring rack to a horizontal position and push the rest of the way in.	10
1. Grasp rack firmly on both sides and pull rack toward you.	10
2. When the stop is reached, tilt rack up and pull the rest of the way out.	10
Telescopic Rack	11
1. Hold the rack on a slight angle.	11
2. Engage the rear hooks in the accessory brackets.	11
3. Hold the rack straight.	11
4. Push the rack in until it is even with the front hooks.	11
5. Lift the rack up.	11
6. Push the rack in completely.	11
7. Engage the rack’s front hooks in the accessory brackets.	11
9 CAUTION	11
Control	12
Touchpads	12
Display Icons	12
Operation	13
About the Appliance	13
Before Using the Appliance for the First Time	13
Basic Features	13
Turning the Oven on and off	13
Setting the Language	13
1. Press INFO.	13
2. Press 2 for “custom”.	13
3. Press 2 for “Language”.	13
4. Use the numeric keys to select your preferred language.	13
The display from step 2 appears in the language you selected.	13
Tips:	13
Setting the Date and Time	14
1. Press CLOCK.	14
2. Enter the current time; for instance, for 11:30, press the keys 1 1 3 0.	14
3. Press CLOCK.	14
4. Press 1 for am or 2 for pm (12-hour-mode).	14
The clock is now set and operating. The menu item “Set date” is displayed:	14
1. Set the clock as described above.	14
2. Enter the current year; for instance, for 2012 press the keys 2 0 1 2.	14
3. Press CLOCK.	14
4. Enter the current month (1-12).	14
5. Press CLOCK.	14
6. Enter the current day of the month.	14
7. Press CLOCK.	14
The date has been set. Date and time are displayed:	14
Tips:	14
User Settings	14
1. Press INFO.	14
2. Press 2 for \	14
3. Select the desired menu item.	14
Tips:	14
Selecting the upper or lower oven	14
Setting the oven mode and temperature	15
1. Press ON/OFF to switch on the oven.	15
2. Double ovens: select the desired oven by pressing UPPER or LOWER.	15
3. Press the desired oven mode.	15
4. Enter the temperature, for instance, press 4 0 0 for 400 °F.	15
5. Press START.	15
The oven starts.	15
Tips:	15
Heating Time Limitation	15
100-200	15
38-93	15
24 h	15
201-550	15
94-288	15
12 h	15
Panel Lock	15
Timer	15
1. Press TIMER.	15
2. Enter length of time, for instance, 10 3 0 for 10 minutes and 30 seconds.	15
3. Press TIMER START/OFF.	15
The timer starts.	15
1. Press TIMER.	15
2. Set a new time.	15
3. Press TIMER START/OFF.	15
Tips:	15
Fast Preheat	16
1. Set the oven mode and temperature as usual.	16
2. Press FAST PREHEAT.	16
3. Press START.	16
Special features	16
Cook Time	16
9 CAUTION	16
1. Set the oven mode and temperature.	16
2. Press COOK TIME.	16
3. Enter the cooking time in hours and minutes. For instance, for 45 minutes, press the numbers 0 4 5.	16
4. Press START.	16
Tips:	16
Stop Time	16
9 CAUTION	16
1. Set a Cook Time first.	17
2. Press STOP TIME.	17
3. Enter the stop time. For instance, for 12:45, press the numbers 1 2 4 5.	17
4. Press START.	17
Tips:	17
Probe	17
1. Insert the probe into the meat as described above.	17
2. Connect the probe to the oven.	17
NOTICE:	17
3. Set the cooking mode and temperature.	17
4. Press PROBE.	17
5. Set the internal temperature for the probe; for instance, press 1 4 5 to set the probe temperature to 145º. See cooking charts for appropriate internal temperatures.	17
6. Press START.	17
Tips:	17
Easy Cook	17
9 CAUTION	17
1. Press EASY COOK.	18
2. Select the function using the numeric keys; for instance, 4 for \	18
3. Select the type of food you want to cook. For instance, press 1 for Rib Eye Roast.	18
4. Choose the level of doneness.	18
5. Use the numeric keys to set the weight, for instance press 3 5 for 3.5 lbs.	18
6. Press START.	18
The remaining programmed cooking time appears in the display. The time when the food will be done cooking is displayed next to the Stop Time symbol. At the end of the programmed time, the oven turns off and a beep sounds. Open the oven door or press ...	18
Tips:	18
Favorites	19
1. Select the cooking mode, cook time and temperature for your favorite dish.	19
2. Press FAVORITES.	19
3. Press numeric key 1 for \	19
4. Select your preferred memory setting.	19
The settings are stored.	19
1. Press FAVORITES.	19
2. Press numeric key 2 to select \	19
3. Select your preferred memory setting.	19
Tips:	19
Sabbath Mode	19
1. Press and hold BAKE for five seconds.	19
2. Press COOK TIME.	19
3. Set the preferred time, for instance, press the keys 3 0 0 0 for 30 hours.	19
4. Press START.	19
The oven starts.	19
Tips:	19
Getting the Most Out of Your Appliance	20
General Tips	20
Pan Placement	20
Aluminum Foil	20
9 WARNING	20
Preheating the Oven	20
Preheat Reminders	20
For Best Results	20
Baking Pans and Dishes	20
High Altitude Baking	20
Condensation	20
Bake %	21
Tips	21
Convection Bake (Some Models) 2	21
Tips	21
True Convection :	22
Tips	22
Roast %	22
Tips	22
Convection Roast 2	22
Tips	22
Broil #	22
Tips	22
Convection Broil 1	22
Tips	22
Pizza 2	23
Tips	23
Speed Convection ‹	23
Tips	23
Proof (Some Models) %	23
Warm %	23
9 CAUTION	23
When using Warm mode, follow these guidelines:	23
Dehydrate :	24
Tips	24
Dehydrate Chart	24
Cleaning and Maintenance	25
Self-Clean	25
9 WARNING	25
When using the Self-Clean setting	25
9 CAUTION	25
Avoid risk of damage	25
1. Press SELF CLEAN.	25
2. Press COOK TIME.	25
3. Depending on the soil level, you can change the length of the Self-Clean mode (1:30 - 2:30 hours). To change the cleaning time to 2 hours and 15 minutes (2:15), press 215.	25
4. Press START.	25
Tips:	25
Avoid These Cleaners	25
Cleaning Guide	25
Maintenance	26
Replacing an Oven Light	26
9 CAUTION	26
when replacing an oven light:	26
1. Turn off power to the oven at the main power supply (fuse or breaker box).	26
2. Remove the oven racks if necessary to provide access to the bulb housing.	26
3. Remove the glass cover by unscrewing it.	26
4. The halogen bulb is visible in the light fixture.	26
5. Remove the halogen bulb by pulling it out of the 2 pin socket. Pull straight down and out.	26
6. Replace with a new halogen bulb. Grasp the new bulb with a clean, dry cloth. Press the 2 pins on the bulb into the socket holes until the bulb is firmly seated.	27
7. Screw the glass cover back on.	27
8. Turn power back on at the main power supply (fuse or breaker box).	27
1. Turn off power to the oven at the main power supply (fuse or breaker box).	27
2. Remove oven racks if necessary to provide access to the bulb housing.	27
3. Optional: remove oven door to provide easier access and visibility.	27
4. Insert the tip of a narrow flat blade screwdriver between the metal clips at about a 40° angle. The screwdriver blade must be able to pass between the metal clips to reach the inner catch.	27
5. (A) Push the screwdriver blade inward to disengage the catch from the slot in the light housing.	27
6. (B) Gently pry the lens off by moving the screwdriver handle away from the oven wall. The lens should detach easily. Do not attempt to force it.	27
7. Pull the halogen bulb from its socket. If it is difficult to grasp the bulb using one hand, use both forefingers to pinch behind the rounded part of the bulb, then pull the bulb out using both hands.	27
8. Replace the halogen bulb. Grasp the new bulb with a clean, dry cloth. Align the bulb prongs with the socket holes and press into place.	27
9. Put the glass cover back on by inserting it into the mounting clip and pressing the end nearest you into the housing until it locks into place.	27
10. Turn power back on at the main power supply (fuse or breaker box).	27
Removing the Oven Door	28
9 CAUTION	28
When removing the oven door:	28
To remove the oven door:	28
1. Read the preceeding caution notice before beginning the oven door removal process.	28
2. Provide a nearby place to safely lay the door after removal so it will not fall over or be stepped upon. Lay the door flat on a blanket or cushioned surface.	28
3. Open the oven door fully until it is parallel to the floor. The door contains powerful springs to assist with closing the door. It is necessary to position the toggle locks in place to take the tension off the springs.	28
4. To access the toggle locks, remove the locking plate using a T20 star head driver.	28
5. After removing the screw, (A) lift the locking plate up and then pivot it out to remove. Repeat for the other hinge. Retain both locking plates and screws for reinstallation.	28
6. Flip the locking levers towards the door as far as they will go. Hint: (B) It may be helptul to use the tip of a screwdriver to pull out the locking levers. (C) Make sure both locking levers are in the locked position pushed all the way towards th...	28
7. With the toggles in place as shown, carefully close the oven door until the front side of the door is about 5½ inches (140 mm) from the control panel.	28
8. Grasp the door firmly using both hands. The door weighs over 30 pounds.	28
9 CAUTION	28
9. Lift the door up and pull out at an upward angle as shown in the following illustration. The notch in the hinge foot will disengage from the oven door frame. With both door hinge feet disengaged, lift the door off the unit.	29
10. Carefully move the door to a safe place to protect it from damage until you are ready to reinstall it.	29
Replacing the Oven Door	29
1. Hold the door firmly in both hands at a 30° angle to the front of the unit.	29
2. Guide the door hinges into the hinge slots on the unit housing.	29
3. Slide the door in until the slots on the hinges engage the oven housing. Hint: it may be necessary to rock the door slightly to seat it correctly.	29
4. Lower the door into the fully open 90° position. If the door will not lower all the way to the 90° position, the hinges are not correctly seated. The door should be straight, not crooked.	29
5. Push the locking toggles back into the unlocked position, toward the oven cavity.	29
6. Reinstall the locking plates and screws (see door removal process above).	29
7. Close the door gently. It should close all the way. Gently open and close the door several times to be sure it is correctly installed and securely in place.	29
Service	29
Troubleshooting Chart	29
Data Plate	30
How to Obtain Service or Parts	30
Cooking Charts	31
The charts can be used as a guide. Follow package or recipe directions.	31
Baked Goods/Entrees	31
Meats	32
The charts can be used as a guide. Follow package or recipe directions.	32
STATEMENT OF LIMITED PRODUCT WARRANTY	34
What this Warranty Covers & Who it Applies to	34
How Long the Warranty Lasts	34
Repair/Replace as Your Exclusive Remedy	34
Out of Warranty Product	35
Warranty Exclusions	35
THERMADOR® Support	36
Service	36
Parts and Accessories	36
Table des MatièresNotice d’utilisation	37
À propos de ce manuel	38
Comment ce manuel est organisé	38
Mots de signalisation pour la sécurité et l'utilisation optimale	38
9 AVERTISSEMENT	38
9 ATTENTION	38
AVIS :	38
Remarque :	38
CONSIGNES DE SÉCURITÉ IMPORTANTES	39
LIRE ET CONSERVER CES CONSIGNES	39
AVERTISSEMENT	39
Installation et entretien corrects	39
AVERTISSEMENT	39
AVERTISSEMENT	39
AVERTISSEMENT	39
AVERTISSEMENT	39
Sécurité-incendie	39
AVERTISSEMENT	39
AVERTISSEMENT	40
AVERTISSEMENT	40
POUR RÉDUIRE LE RISQUE DE LÉSIONS CORPORELLES DANS L'ÉVENTUALITÉ D'UN FEU DE GRAISSE, OBSERVER LES CONSIGNES SUIVANTES :	40
a. ÉTOUFFER LES FLAMMES à l'aide d'un couvercle bien hermétique, d'une tôle à biscuits ou d'un plateau en métal, puis éteindre l'appareil. FAIRE ATTENTION À NE PAS SE BRÛLER. Si les flammes ne s'éteignent pas immédiatement, ÉVACUER LES LI...	40
b. NE JAMAIS SAISIR UN RÉCIPIENT QUI BRÛLE. Vous pourriez vous brûler.	40
c. NE PAS UTILISER D'EAU, y compris les chiffons ou serviettes mouillées. Une violente explosion de vapeur risque de se produire.	40
d. Utiliser un extincteur uniquement si :	40
Prévention des brûlures	40
ATTENTION	40
Sécurité des enfants	41
ATTENTION	41
Consignes en matière de nettoyage	41
Sécurité pour la batterie de cuisine	41
AVIS :	41
Mise en route	42
Pièces	42
Ventilateur de refroidissement	42
Évent du four	42
Ventilateur à convection	43
Sole du four	43
9 AVERTISSEMENT	43
Accessoires	43
Mise en place de la grille	43
9 ATTENTION	43
Grille plate	43
1. Saisir fermement la grille par les côtés.	43
2. Installer la grille (voir illustration).	43
3. Incliner la grille vers le haut pour mettre la butée dans le guide.	43
4. Amener la grille en position horizontale et pousser jusqu'au fond.	43
1. Saisir fermement la grille par les côtés et tirer vers soi.	43
2. Lorsque la butée est atteinte, incliner vers le haut et tirer complètement vers soi.	43
Grille télescopique	44
1. Tenir la grille en l'inclinant légèrement.	44
2. Insérer les crochets arrière dans les supports d'accessoires.	44
3. Tenir la grille en position horizontale.	44
4. Introduire la grille jusqu'à ce qu'elle soit alignée avec les crochets avant.	44
5. Soulever la grille.	44
6. Pousser la grille jusqu'au fond.	44
7. Introduire les crochets avant de la grille dans les supports d'accessoires.	44
9 ATTENTION	44
Tableau de commande	45
Touches à effleurement	45
Symbole d'affichage	46
Fonctionnement	46
Concernant cet appareil	46
Avant la première utilisation	46
Fonctionnalités de base	46
Activation et désactivation du four	46
Paramétrage de la langue	46
1. Appuyer sur INFO.	46
2. Pour \	47
3. Pour \	47
4. Utiliser les touches numériques pour programmer le langage désiré.	47
L'affichage de l'étape 2 apparaît dans la langue que vous avez sélectionnée.	47
Conseils :	47
Paramétrage de la date et de l'heure	47
1. Appuyer sur CLOCK.	47
2. Saisir l'heure actuelle ; par exemple, pour 11 h 30, appuyer sur les touches 1 1 3 0.	47
3. Appuyer sur CLOCK.	47
4. Appuyer sur 1 pour \	47
L'horloge est maintenant programmée et fonctionnelle. L'élément de menu \	47
1. Programmer l'horloge comme indiqué précédemment.	47
2. Saisir l'année en cours ; par exemple, pour 2012, appuyer sur les touches 2 0 1 2.	47
3. Appuyer sur CLOCK.	47
4. Saisir le mois en cours (1 à 12).	47
5. Appuyer sur CLOCK.	47
6. Saisir le jour actuel du mois.	47
7. Appuyer sur CLOCK.	47
La date a été programmée. La date et l'heure sont affichées :	47
Conseils :	47
Paramètres utilisateur	47
1. Press INFO.	48
2. Pour \	48
3. Sélectionner l'élément de menu désiré.	48
Conseils :	48
Sélection du four supérieur ou inférieur	48
Paramétrage du mode du four et de la température	48
1. Appuyer sur ON/ OFF (MARCHE/ARRÊT) pour mettre le four sous tension.	48
2. Fours doubles : pour sélectionner le four désiré, appuyer sur UPPER (SUPÉRIEUR) ou LOWER (INFÉRIEUR).	48
3. Appuyer sur le mode désiré.	48
4. Saisir la température, par exemple pour 400 °F (204 °C), appuyer sur 4 0 0.	48
5. Appuyer sur START (DÉPART).	48
Le four se met en marche.	48
Conseils :	48
Limitation du temps de chauffage	48
100-200	49
38-93	49
24 h	49
201-550	49
94-288	49
12 h	49
Verrouillage du tableau de commande	49
Minuterie (Timer)	49
1. Appuyer sur TIMER (MINUTERIE).	49
2. Saisir la durée, par exemple, 10 30 pour 10 minutes et 30 secondes.	49
3. Appuyer sur TIMER START/OFF (DÉPART/ARRÊT MINUTERIE).	49
La minuterie se déclenche.	49
1. Appuyer sur TIMER (MINUTERIE).	49
2. Définir la nouvelle durée.	49
3. Appuyer sur TIMER START/OFF (DÉPART/ARRÊT MINUTERIE).	49
Conseils :	49
Préchauffage rapide	49
1. Régler le mode du four et la température comme à l'accoutumée.	49
2. Appuyer sur FAST PREHEAT.	49
3. Appuyer sur START.	49
Fonctions spéciales	50
Temps de cuisson (Cook Time)	50
9 ATTENTION	50
1. Régler le mode du four et la température.	50
2. Appuyer sur COOK TIME.	50
3. Saisir le temps de cuisson en heures et en minutes. Par exemple, pour 45 minutes de cuisson, appuyer sur les chiffres 0 4 5.	50
4. Appuyer sur START.	50
Conseils :	50
Heure d'arrêt	50
9 ATTENTION	50
1. Régler tout d'abord la durée de cuisson.	50
2. Appuyer sur STOP TIME (heure d'arrêt).	50
3. Entrer l'heure d'arrêt. Par exemple pour indiquer 12:45, appuyer sur les chiffres 1 2 4 5.	50
4. Appuyer sur START (démarrage).	50
Conseils :	51
Sonde (Probe - certains modèles)	51
1. Introduire la sonde dans la viande comme décrit ci- dessus.	51
2. Brancher la sonde sur le four.	51
Remarque :	51
3. Régler le mode de cuisson et la température.	51
4. Appuyer sur PROBE (SONDE).	51
5. Régler la température interne de la sonde ; par exemple, pour régler la température de la sonde sur 145°, appuyer sur 1 4 5. Voir les tableaux de cuisson pour obtenir les températures internes appropriées.	51
6. Appuyer sur START (DÉPART).	51
Conseils :	51
Cuisson automatique (Easy Cook)	51
9 ATTENTION	51
1. Appuyer sur EASY COOK.	52
2. électionner la fonction à l'aide des touches numériques ; par exemple, 4 pour \	52
3. Sélectionner le type d'aliment que vous voulez cuisiner. Par exemple, pour \	52
4. Choisir le niveau de cuisson.	52
5. Utiliser les touches numériques pour programmer le poids, par exemple pour 3.5 lb, appuyer sur 3 5.	52
6. Appuyer sur START	52
La durée de cuisson programmée restante apparaît sur l'affichage. L'heure à laquelle la cuisson sera terminée est affichée près du symbole Heure d'arrêt. À la fin du temps programmé, le four s'éteint et un signal sonore retentit. Ouvrir la...	52
Conseils :	52
Favorites (favoris)	53
1. Sélectionnez le mode de cuisson, le temps de cuisson et la température de votre plat favoris.	53
2. Appuyer sur FAVORITES (favoris).	53
3. Appuyer sur la touche 1 pour sauvegarder le réglage.	53
4. Sélectionner le réglage de mémoire voulu.	53
Les réglages sont entrés en mémoire.	53
1. Appuyer sur FAVORITES (favoris).	53
2. Appuyer sur la touche 2 pour sélectionner \	53
3. Sélectionner le réglage de mémoire voulu.	53
Conseils :	53
Mode Sabbat (Sabbath Mode)	53
1. Appuyer et maintenir enfoncée la touche BAKE pendant cinq secondes.	53
2. Appuyer sur COOK TIME.	53
3. Programmer le temps désiré ; par exemple, pour 30 heures, appuyer sur les touches 3 0 0 0.	53
4. Appuyer sur START.	53
Le four se met en marche.	53
Conseils :	53
Tirer le meilleur parti de votre appareil	54
Conseils généraux	54
Mise en place des ustensiles de cuisson	54
Papier aluminium	54
9 AVERTISSEMENT	54
Préchauffer le four	54
Préchauffage Rappels	54
Pour de meilleurs résultats	54
Moules et plats	54
Cuisson à haute altitude	55
Condensation	55
Bake (Cuisson) %	55
Conseils	55
Convection Bake (Cuisson par convection - certains modèles) 2	55
Conseils	55
True Convection ( Convection authentique) :	56
Conseils	56
Roast (Rôtissage) %	56
Conseils	56
Convection Roast (Rôtissage par convection) 2	56
Conseils	56
Broil (Cuisson au gril)#	57
Conseils	57
Convection Broil (Cuisson au gril par convection) 1	57
Conseils	57
Pizza 2	57
Conseils	57
Speed Convection (Convection rapide) ‹	58
Conseils	58
Proof (Apprêt - certains modèles) %	58
Warm (Maintien au chaud) %	58
9 ATTENTION	58
lors de l'utilisation du mode de maintien au chaud, suivre les recommandations suivantes :	58
Dehydrate (Dessiccation) :	58
Conseils	58
Tableau de dessiccation	59
Nettoyage et entretien	60
Autonettoyage	60

Match case Limit results 1 per page

Maintenance

Replacing an Oven Light

CAUTION

WHEN REPLACING AN OVEN LIGHT:

▯

Make sure the appliance and lights are cool and

power to the appliance has been turned off

before replacing the light bulb(s). Failure to do so

could result in electrical shock or burns.

▯

The lenses must be in place when using the

appliance.

▯

The lenses serve to protect the light bulb from

breaking.

▯

The lenses are made of glass. Handle carefully to

avoid breaking. Broken glass could cause an

injury.

▯

Light socket is live when door is open.

Use only 120 volt, 25 watt halogen light bulbs, G9 base.

These bulbs can be purchased through retail stores.

Use a clean, dry cloth to handle halogen light bulbs. This

will increase the life of the bulb.

Hint: Some users may find it helpful to remove the oven

door to provide easier access and visibility. See the

following section: “Removing the oven door".

To replace the halogen bulb on the oven ceiling:

Turn off power to the oven at the main power supply

(fuse or breaker box).

Remove the oven racks if necessary to provide access

to the bulb housing.

Remove the glass cover by unscrewing it.

The halogen bulb is visible in the light fixture.

Remove the halogen bulb by pulling it out of the 2 pin

socket. Pull straight down and out.

Painted Surfaces

Clean with hot soapy water or

apply Fantastik® or Formula

409® to a clean sponge or

paper towel and wipe clean.

Avoid using powder cleaning

agents, steel wool pads and

oven cleaners.

Porcelain Surfaces

Immediately wipe up acid spills

like fruit juice, milk and tomatoes

with a dry cloth. Do not use a

moistened sponge/cloth on hot

porcelain. When cool, clean with

hot soapy water or apply Bon-

Ami® or Soft Scrub® to a damp

sponge. Rinse and dry. For stub-

born stains, use soap-filled pads.

It is normal for porcelain to show

fine lines with age due to expo-

sure to heat and food soil.

Stainless Steel Sur-

faces

Always wipe or rub in the direc-

tion of the grain. Clean with a

soapy sponge, then rinse and

dry, or wipe with Fantastik® or

Formula 409® sprayed on a

paper towel. Protect and polish

with Stainless Steel Magic® and

a soft cloth. Remove water spots

with a cloth dampened with white

vinegar. Use Bar Keeper´s

Friend® to remove heat discolor-

ation.

Plastic & Controls

When cool, clean with soapy

water, rinse and dry.

Probe

Wipe with soapy water. Do not

submerge. Do not wash in the

dishwasher.

Printed areas (words

& numbers)

Do not use abrasive cleaners or

petroleum based solvents.

Part

Recommendations