Thermador PRG486JDG Installation Manual - Page 20

Installing a Backsplash with a Keep Hot, Shelf

Get Thermador PRG486JDG PDF manuals and user guides View all Thermador PRG486JDG manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

Installing a Backsplash with a Keep Hot Shelf 1. Locate wall studs. • Wall studs are usually installed with a 16" (406mm) or 24" (1372mm) space on center. 2. The height of the hood will determine the height of the top edge of the backsplash. The backsplash should be mounted so that the bottom rear edge of the Keep Hot Shelf overlaps the backsplash 11/2" (38mm). 3. At the locations indicated in Figure 13, mount the lower shelf brackets included with the Keep Hot Shelf through the Backsplash and into the wall studs. • Due to variable wall stud widths and varying backsplash widths, in some cases, only one wall stud may be found at the mounting location. 4. Remove backsplash protective covering. 5. Start with the Keep Hot Shelf Installation. Figure 12: Backsplash with a Keep Hot Shelf A hood can be installed first if the Backsplash is to be installed with a Keep Hot Shelf given that the Keep Hot Shelf covers the top mounting screws of the Backsplash (Figure 12). • To protect against scratches, leave protective film on the backsplash until after installation is complete. • If range is already installed, refer to the manufacture's instructions to disconnect gas and power supplies. Move range forward to gain access to rear of unit. IncLlouwdeerdSWhietlhf BKreaecpkHetost Shelf Figure 13: Backsplash with a Keep Hot Shelf English 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
English 18
Installing a Backsplash with a Keep Hot
Shelf
A hood can be installed first if the Backsplash is to be
installed with a Keep Hot Shelf given that the Keep Hot
Shelf covers the top mounting screws of the Back-
splash (Figure 12).
•
To protect against scratches, leave protective film on
the backsplash until after installation is complete.
•
If range is already installed, refer to the manufacture’s
instructions to disconnect gas and power supplies.
Move range forward to gain access to rear of unit.
1.
Locate wall studs.
•
Wall studs are usually installed with a 16” (406mm)
or 24” (1372mm) space on center.
2.
The height of the hood will determine the height of the
top edge of the backsplash. The backsplash should be
mounted so that the bottom rear edge of the Keep Hot
Shelf overlaps the backsplash 1
1
/
2
” (38mm).
3.
At the locations indicated in Figure 13, mount the lower
shelf brackets included with the Keep Hot Shelf
through the Backsplash and into the wall studs.
•
Due to variable wall stud widths and varying
backsplash widths, in some cases, only one wall
stud may be found at the mounting location.
4.
Remove backsplash protective covering.
5.
Start with the Keep Hot Shelf Installation.
Figure 12:
Backsplash with a Keep Hot Shelf
Figure 13:
Backsplash with a Keep Hot Shelf
Lower Shelf Brackets
Included With Keep Hot Shelf