Thermador T36BT820NS Installation Manual - Page 14

Attaching the anti-tip-brackets

Get Thermador T36BT820NS PDF manuals and user guides View all Thermador T36BT820NS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

1. Attaching the anti-tip-brackets , WARNING: Risk of injury and damage! Assure that there are no electrical wires or plumbing in the area which the screws could penetrate. , CAUTION: Risk of injury! Always wear safety glasses and other necessary protective devices or apparel when installing or working with dowels. Note:  2 anti-tip-brackets are required for the appliance.  The supplied set contains fastening screws for various applications. Select the fastening screws according to the local conditions. The anti-tip-brackets (a) must overlap a minimum of 21/8" (54 mm) over the appliance to secure the appliance. If this minimum length cannot be observed for structural conditions it is possible to do this by fastening a spacer (b) behind the anti-tip angle, e.g. a sufficiently dimensioned wood board. The length of the plank should correspond to the width of the installation niche! 1. Specify the attachment points of the anti-tip-brackets according to the section on "Installation dimensions". 2. Attach the anti-tip-brackets completely. Be sure screws hold tight. Important notes for fastening with dowels and screws: Not recommended for use in light-weight masonry material such as cinder block. Not recommended for use in new concrete which has not had time to cure. 14

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
14
1.
Attaching the anti-tip-brackets
,
WARNING:
Risk of injury and damage!
Assure that there are no electrical wires or
plumbing in the area which the screws could
penetrate.
,
CAUTION:
Risk of injury! Always wear safety glasses and
other necessary protective devices or apparel
when installing or working with dowels.
Note:
2 anti-tip-brackets are required for the appliance.
The supplied set contains fastening screws for
various applications. Select the fastening screws
according to the local conditions.
The anti-tip-brackets (a) must overlap a minimum of
2
1
/
8
” (54 mm) over the appliance to secure
the appliance.
If this minimum length cannot be observed for structural
conditions it is possible to do this by fastening
a spacer (b) behind the anti-tip angle, e.g. a sufficiently
dimensioned wood board.
The length of the plank should correspond to the width
of the installation niche!
1.
Specify the attachment points of the anti-tip-brackets
according to the section on “Installation
dimensions”.
2.
Attach the anti-tip-brackets completely.
Be sure screws hold tight.
Important notes for fastening with dowels and screws:
Not recommended for use in light-weight masonry
material such as cinder block.
Not recommended for use in new concrete which has not
had time to cure.