Thermador T36BT820NS Installation Manual - Page 17

Pushing the appliance into the installation, enclosure

Get Thermador T36BT820NS PDF manuals and user guides View all Thermador T36BT820NS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

5. Pushing the appliance into the installation enclosure , CAUTION: Caution when pushing the appliance into the installation enclosure. Do not damage the water line or power cord. Note: When the floor or the appliance is not leveled in comparison to the installation enclosure adjust height adjustable wheels before you move the appliance into the installation enclosure. 1. Put the mains plug into the socket. 2. Push the water line into the guard tube (a) at the rear of the appliance. , WARNING: Be careful, otherwise people who are helping may be injured or the appliance may be damaged! The appliance may tip over while the water line is pushing into the guard tube (a). 3. To prevent the power cord from becoming caught, tie a piece of string to the middle of the power cord and feed forwards over the top of the appliance. When pushing in the appliance, pull the cable upwards. Take care not to pinch the power cord. or Using adhesive tape, tape the power cord to the floor centrally behind the appliance approx. 15" (380 mm) away from the rear panel of the installation enclosure. 4. Carefully push the appliance to the half into the installation enclosure. 5. Remove transportation protection device from the underside of the freezer compartment drawer. 6. Loosen and unscrew nuts on the top of the drawer. Note: However, do not turn the threaded bolts, otherwise the door will no longer be aligned. 7. Loosen the screws on the left and right fixing brackets. Do not unscrew the screws! 17

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
17
5.
Pushing the appliance into the installation
enclosure
,
CAUTION:
Caution when pushing the appliance into the
installation enclosure. Do not damage the water
line or power cord.
Note:
When the floor or the appliance is not leveled in
comparison to the installation enclosure adjust height
adjustable wheels before you move the appliance into
the installation enclosure.
1.
Put the mains plug into the socket.
2.
Push the water line into the guard tube (a) at the rear
of the appliance.
,
WARNING:
Be careful, otherwise people who are helping may
be injured or the appliance may be damaged!
The appliance may tip over while the water line is
pushing into the guard tube (a).
3.
To prevent the power cord from becoming caught,
tie a piece of string to the middle of the power cord
and feed forwards over the top of the appliance.
When pushing in the appliance, pull the cable
upwards. Take care not to pinch the power cord.
or
Using adhesive tape, tape the power cord to the
floor centrally behind the appliance approx.
15" (380 mm) away from the rear panel of
the installation enclosure.
4.
Carefully push the appliance
to the half
into the
installation enclosure.
5.
Remove transportation protection device from the
underside of the freezer compartment drawer.
6.
Loosen and unscrew nuts on the top of the drawer.
Note:
However, do not turn the threaded bolts, otherwise
the door will no longer be aligned.
7.
Loosen the screws on the left and right fixing
brackets. Do not unscrew the screws!