Thermador T36BT820NS Installation Manual - Page 19

Aligning the appliance in the, installation enclosure

Get Thermador T36BT820NS PDF manuals and user guides View all Thermador T36BT820NS manuals
Add to My Manuals
Save this manual to your list of manuals

Page 19 highlights

1. Aligning the appliance in the installation enclosure Note:  To ensure that the appliance functions correctly, it must be set perfectly levelled.  Do not twist or jam the appliance inside the installation enclosure! When adjusting the heightadjustable feet, proceed gradually: Always alternate between left and right, etc.  For easier adjustment of the rear feet take the weight off by slightly tilting the appliance forward.  Do not bend the appliance against the anti-tipbrackets. 1. Align the appliance with the cabinet fronts. The mark (a) attached at the appliance base is used as a standard gage for height adjustment. When adjusting the height, align this mark at a height of 11/2" (32 mm) above the floor. It is very important to comply with this dimension for the subsequent alignment of the furniture fronts. The height adjustment gauge (b) is used to set this height correctly. The upper edge of the gauge must be in alignment with the mark on the appliance. 2. Unscrew the feet at the front of the appliance until the mark (a) on the appliance is in alignment with the upper edge of the height adjustment gauge (b). 3. Align the appliance vertically using the feet at the back. Use a level! The height-adjustable feet at the front and rear can all be adjusted from the front. Front: with open-ended wrench 1/2" (Width across flats 13 mm) Rear: with 5/16" (8 mm) hex nut driver via flexible shaft. 19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
19
1.
Aligning the appliance in the
installation enclosure
Note:
To ensure that the appliance functions correctly,
it must be set perfectly levelled.
Do not twist or jam the appliance inside the
installation enclosure! When adjusting the height-
adjustable feet, proceed gradually: Always alternate
between left and right, etc.
For easier adjustment of the rear feet take the weight
off by slightly tilting the appliance forward.
Do not bend the appliance against the anti-tip-
brackets.
1.
Align the appliance with the cabinet fronts.
The height-adjustable feet at the front and rear can all be
adjusted from the front.
Front:
with open-ended wrench
1
/
2
"
(Width across flats 13 mm)
Rear:
with
5
/
16
" (8 mm) hex nut driver via flexible
shaft.
The mark (a) attached at the appliance base is used as
a standard gage for height adjustment. When adjusting
the height, align this mark at a height of 1
1
/
2
" (32 mm)
above the floor. It is very important to comply with this
dimension for the subsequent alignment of the furniture
fronts.
The height adjustment gauge (b) is used
to set this height correctly. The upper
edge of the gauge must be in alignment
with the mark on the appliance.
2.
Unscrew the feet at the front of the appliance
until the mark (a) on the appliance is in alignment
with the upper edge of the height adjustment
gauge (b).
3.
Align the appliance vertically using the feet
at the back. Use a level!