Toshiba e405 User Manual - Page 10

CE compliance, FCC Notice, Declaration of Conformity

Page 10 highlights

• Automotive Environments • Aircraft Environments Any consequences resulting from the use of this product in working environments that are not approved are not the responsibility of Toshiba Corporation. The consequences of the use of this product in non-approved working environments may be: • Interference with other devices or machines in the nearby surrounding area • Malfunction of, or data loss from, this product caused by disturbances generated by other devices or machines in the nearby surrounding area Therefore Toshiba strongly recommends that the electromagnetic compatibility of this product be suitably tested in all non-approved working environments before use. In the case of automobiles or aircraft, the manufacturer or airline respectively should be asked for permission before use of this product. Furthermore, for general safety reasons, the use of this product in environments with explosive atmospheres is not permitted. CE compliance This product and the original options are designed to observe the related EMC (Electromagnetic compatibility) and safety standards. However, Toshiba cannot guarantee that this product still observes these EMC standards if options or cables not produced by Toshiba are connected or implemented. In this case the persons who have connected/implemented those options/cables have to make sure that the system (PC plus options/ cables) still fulfils the required standards. To avoid general EMC problems, the following advice should be observed: • Only CE marked options should be connected/implemented • Only best shielded cables should be connected FCC Notice "Declaration of Conformity" This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful 10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118

10
Automotive Environments
Aircraft Environments
Any consequences resulting from the use of this product in working envi-
ronments that are not approved are not the responsibility of Toshiba Cor-
poration.
The consequences of the use of this product in non-approved working
environments may be:
Interference with other devices or machines in the nearby surrounding
area
Malfunction of, or data loss from, this product caused by disturbances
generated by other devices or machines in the nearby surrounding
area
Therefore Toshiba strongly recommends that the electromagnetic com-
patibility of this product be suitably tested in all non-approved working
environments before use. In the case of automobiles or aircraft, the man-
ufacturer or airline respectively should be asked for permission before use
of this product.
Furthermore, for general safety reasons, the use of this product in envi-
ronments with explosive atmospheres is not permitted.
CE compliance
This product and the original options are designed to observe the related
EMC (Electromagnetic compatibility) and safety standards. However,
Toshiba cannot guarantee that this product still observes these EMC stan-
dards if options or cables not produced by Toshiba are connected or
implemented. In this case the persons who have connected/implemented
those options/cables have to make sure that the system (PC plus options/
cables) still fulfils the required standards. To avoid general EMC prob-
lems, the following advice should be observed:
Only CE marked options should be connected/implemented
Only best shielded cables should be connected
FCC Notice
“Declaration of Conformity”
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accor-
dance with the instructions, may cause harmful interference to radio com-
munications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful