Tripp Lite SU3000XL Owner's Manual for SmartOnline UPS 932470 - Page 9

Communications

Get Tripp Lite SU3000XL PDF manuals and user guides View all Tripp Lite SU3000XL manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

Basic Operation continued Telephone/Network Protection Jacks: These jacks protect your equipment against surges over a telephone/network data line. Connecting your equipment to these jacks is optional. Your UPS will work properly without this connection. Not compatible with PoE (Power Over Ethernet) applications. Communications Communications Ports (USB or RS-232): These ports connect your UPS to any workstation or server. Use with Tripp Lite's PowerAlert Software and included cables to enable your computer to automatically save open files and shut down equipment during a blackout. Also use PowerAlert Software to monitor a wide variety of AC line power and UPS operating conditions. Consult your PowerAlert Software manual or contact Tripp Lite Customer Support for more information. See "USB and RS-232 Serial Communications" in the "Optional Connections" section for installation instructions. Dry contact communications are simple, but some knowledge of electronics is necessary to configure them. The DB9 port's pin assignments are shown in the diagram. If the UPS battery is low, the UPS sends a signal by bridging pins 1 and 5. If utility power fails, the UPS sends a signal by bridging pins 8 and 5. To shut the UPS down remotely, short pin 3~pin 9 for at least 3.8 seconds. EPO (Emergency Power Off) Port: Your UPS features a EPO port that may be used to connect the UPS to a contact closure switch to enable emergency inverter shutdown. See Optional Installation. 9 201102091 93-3092.indb 9 3/29/2011 5:36:47 PM

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
9
Basic Operation
continued
Telephone/Network Protection Jacks:
These jacks protect your
equipment against surges over a telephone/network data line. Connecting
your equipment to these jacks is optional. Your UPS will work properly
without this connection. Not compatible with PoE (Power Over Ethernet)
applications.
Communications
Communications Ports (USB or RS-232):
These ports connect your UPS
to any workstation or server. Use with Tripp Lite’s PowerAlert Software and
included cables to enable your computer to automatically save open files
and shut down equipment during a blackout. Also use PowerAlert Software
to monitor a wide variety of AC line power and UPS operating conditions.
Consult your PowerAlert Software manual or contact Tripp Lite Customer
Support for more information. See “USB and RS-232 Serial
Communications” in the “Optional Connections” section for installation
instructions.
Dry contact communications are simple, but some knowledge of
electronics is necessary to configure them. The DB9 port’s pin assignments
are shown in the diagram. If the UPS battery is low, the UPS sends a signal
by bridging pins 1 and 5. If utility power fails, the UPS sends a signal by
bridging pins 8 and 5. To shut the UPS down remotely, short pin 3~pin 9
for at least 3.8 seconds.
EPO (Emergency Power Off) Port:
Your UPS features a EPO port that
may be used to connect the UPS to a contact closure switch to enable
emergency inverter shutdown. See Optional Installation.
201102091 93-3092.indb
9
3/29/2011
5:36:47 PM