ViewSonic PJ862 User Manual - Page 45

NETWORK Menu continued

Get ViewSonic PJ862 PDF manuals and user guides View all ViewSonic PJ862 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 45 highlights

Multifunctional settings NETWORK Menu (continued) This projector provides the NETWORK function. When you start to use this function, please consult your dealer for further information. To start, connect the LAN port to a gateway device via a CAT-5 cable, then set up the projector according to the Network environment in which you use it. When your network enables the DHCP function You can set automatically, if you set the DHCP function to TURN ON using the NETWORK menu. Please refer to the section NETWORK menu (40). When your network doesn't support the DHCP function or when you use a fixed address even if your network can support the DHCP function Please set the IP address, the subnet mask, the default gateway and the DHCP using the NETWORK menu. At first, set the DHCP function to TURN OFF. It is also possible to configure the projector's network settings using a Web browser (Internet Explorer 5.0 or higher; Netscape 6.2 or higher) on a computer connected to the network. When using a Web browser to configure the projector's network settings, password access is required. However, since a password is not configured when the product is shipped from the factory, if a password has not been configured, then you can simply click on Login without entering a password to access the Projector Network Configuration dialog. To configure the settings using a Web browser, proceed as follows: ex. Case of IP Address = 192.168.1.10 Screen 1 1. Enter http://192.168.1.10 into the Web browser's address field. 2. Once Screen 1 is displayed (as shown on the right), enter the password and then click on "Login". 3. Once Screen 2 is displayed (as shown on the right), select the desired item by clicking the corresponding ENTER button. Information Screen 2 Allows you to confirm the current network settings. (Screen 3) IP Configuration Allows you to configure IP address, subnet mask and default gateway if DHCP is disabled. (Screen 4) DHCP Setting Allows you to enable or disable DHCP. (Screen 5) Password Setting Allows you to change the login password. (Screen 6) ViewSonic PJ862 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
41
ViewSonic
PJ862
Multifunctional settings
NETWORK Menu (continued)
This projector provides the NETWORK function. When you start to use this function, please
consult your dealer for further information.
To start, connect the LAN port to a gateway device via a CAT-5 cable, then set up the
projector according to the Network environment in which you use it.
When your network enables the DHCP function
Y
ou can set automatically, if you set the DHCP function to TURN ON using the NETWORK
menu. Please refer to the section NETWORK menu (
40
).
When your network doesn't support the DHCP function or when
you use a fixed address even if your network can support the
DHCP function
Please set the IP address, the subnet mask, the default gateway and the DHCP using the
NETWORK menu. At first, set the DHCP function to TURN OFF.
It is also possible to configure the projector's network settings using a Web browser (Internet
Explorer 5.0 or higher; Netscape 6.2 or higher) on a computer connected to the network.
When using a Web browser to configure the projector's network settings, password access
is required. However, since a password is not configured when the product is shipped from
the factory, if a password has not been configured, then you can simply click on Login
without entering a password to access the Projector Network Configuration dialog.
To configure the settings using a Web browser, proceed as follows:
ex. Case of IP Address = 192.168.1.10
1.
E
nter http://192.168.1.10 into the Web browser's
address field.
2.
Once Screen 1 is displayed (as shown on the
right), enter the password and then click on
"Login".
3.
Once Screen 2 is displayed (as shown on the
right), select the desired item by clicking the
corresponding ENTER button.
Information
Allows you to confirm the current network settings.
(Screen 3)
IP Configuration
Allows you to configure IP address, subnet mask and
default gateway if DHCP is disabled. (Screen 4)
DHCP Setting
Allows you to enable or disable DHCP. (Screen 5)
Password Setting
Allows you to change the login password. (Screen 6)
Screen 1
Screen 2