Weber Genesis Jr LP Owner Manual - Page 33

Fitting, Replacement

Get Weber Genesis Jr LP PDF manuals and user guides View all Weber Genesis Jr LP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 33 highlights

P0L Fitting "O" Ring Replacement POL nut "O" ring groove POL tip "O" ring Figure 15 Body of POL Figure 16 Whenever the POL fitting is disconnected, you should check the condition of the "O" ring. Figure 15. If the "O" ring appears damaged, obtain a replacement from Weber-Stephen Products Customer Service Center. Replacement "O" Ring part number [4086976]. WARNING: Do not use barbecue if "O" ring is damaged or missing. Figure 17 Figure 18 TO REPLACE "O" RING: The "O" ring is seated in a groove. The POL fitting is made of brass. Do not use any tool that will damage the tip of the POL or the "O" ring groove. Use a soft material (a toothpick) to remove "O" ring from groove. Figure 16. Inspect POL tip and groove for rough spots. Figure 17. Carefully install new "O" Ring into groove. Figure 18. Make sure it is fully seated in the groove. WARNING: No sealant is required on the POL fitting. Do not use pipe dope, tape or any other type of sealant on the POL fitting or LP tank. Screw regulator POL into tank and leak check with a soap and water solution, before operation of barbecue. 33

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
P0L
Fitting
"O"
Ring
Replacement
POL
nut
"O"
ring
groove
POL
tip
"O"
ring
Figure
15
Body
of
POL
Figure
16
Whenever
the
POL
fitting
is
disconnected,
you
should
check
the
condition
of
the
"O"
ring.
Figure
15.
If
the
"O"
ring
appears
damaged,
obtain
a
replacement
from
Weber
-Stephen
Products
Customer
Service
Center.
Replacement
"O"
Ring
part
number
[4086976].
WARNING:
Do
not
use
barbecue
if
"O"
ring
is
damaged
or
missing.
Figure
17
Figure
18
TO
REPLACE
"O"
RING:
The
"O"
ring
is
seated
in
a
groove.
The
POL
fitting
is
made
of
brass.
Do
not
use
any
tool
that
will
damage
the
tip
of
the
POL
or
the
"O"
ring
groove.
Use
a
soft
material
(a
toothpick)
to
remove
"O"
ring
from
groove.
Figure
16.
Inspect
POL
tip
and
groove
for
rough
spots.
Figure
17.
Carefully
install
new
"O"
Ring
into
groove.
Figure
18.
Make
sure
it
is
fully
seated
in
the
groove.
WARNING:
No
sealant
is
required
on
the
POL
fitting.
Do
not
use
pipe
dope,
tape
or
any
other
type
of
sealant
on
the
POL
fitting
or
LP
tank.
Screw
regulator
POL
into
tank and
leak
check
with
a
soap
and
water
solution,
before
operation
of
barbecue.
33