Weider 8530 User Manual - Page 11

Locate the Short Cable 23. - parts

Get Weider 8530 PDF manuals and user guides View all Weider 8530 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

CABLE ASSEMBLY 17. Route the Medium Cable (58) around the 3 1/2" Pulley (15) attached to the bracket on the Top Frame (55). Tighten the 3/8" x 2" Bolt (12) and the 3/8" Nylon Locknut (21). (Note: This Pulley is pre-assembled. It has been shown disassembled for easy part identification.) Be sure that the Cable is in the groove of the Pulley and that the Cable and Pulley move smoothly. 18. Remove the 3 1/2" Low Pulley (95) from the Press Frame (17). Reattach the Pulley with the 5/8" x 9/16" Spacer (7) between the Pulley and the Press Frame. Hand-tighten the 3/8" Nylon Locknut (21). Locate the Short Cable (23). Route the Short Cable under the 3 1/2" Low Pulley (95). Be sure that the end of the Cable with the ball is on the indicated side of the Press Frame (17) and that the Cable is between the Pulley and the crossbar on the Press Frame. Tighten the 3/8" Nylon Locknut (21) and 3/8" x 3 3/4" Bolt (88). Route the Short Cable (23) around the 3 1/2" Pulley (15) attached to the lower hole in the Front Upright (42). Be sure that the Cable Trap (not shown) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown. Tighten the 3/8" Nylon Locknut (21) and 3/8" x 3 3/4" Bolt (not shown). 19. Route the Short Cable (23) around the 3 1/2" Pulley (15) attached to the upper hole in the Press Frame (17). Be sure that the Cable Trap (66) is in the "3 o'clock" position and that the Cable is routed around the Pulley as shown. Tighten the 3/8" Nylon Locknut (21) and 3/8" x 3 1/2" Bolt (not shown). Route the Short Cable (23) around the 3 1/2" Pulley (15) attached to the upper hole in the Front Upright (42). Be sure that the Cable Trap (not shown) is turned to hold the Cable in place and that the Cable is routed around the Pulley as shown. Tighten the 3/8" Nylon Locknut (21) and 3/8" x 3 3/4" Bolt (not shown). 20. Attach the end of the Short Cable (23) to the Long "U"-Bracket (57) with a 1/4" Nylon Locknut (2) and a 1/4" Flat Washer (10). Do not tighten the 1/4" Nylon Locknut. It should be threaded onto the Cable only a couple of turns. 17 55 15 12 Bracket 58 21 18 15 21 42 17 23 9 88 Ball 7 95 Crossbar 21 19 21 42 15 23 15 21 66 12 9 3 6 17 20 2 57 10 23 11

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
11
17. Route the Medium Cable (58) around the
3 1/2” Pulley (15) attached to the bracket on
the Top Frame (55). Tighten the 3/8” x 2” Bolt
(12) and the 3/8” Nylon Locknut (21). (Note:
This Pulley is pre-assembled. It has been
shown disassembled for easy part identifica-
tion.)
Be sure that the Cable is in the
groove of the Pulley and that the Cable
and Pulley move smoothly.
18. Remove the 3 1/2” Low Pulley (95) from the
Press Frame (17). Reattach the Pulley with
the 5/8” x 9/16” Spacer (7) between the
Pulley and the Press Frame.
Hand-tighten
the 3/8” Nylon Locknut (21).
Locate the Short Cable (23).
Route the
Short Cable under the 3 1/2” Low Pulley (95).
Be sure that the end of the Cable with the
ball is on the indicated side of the Press
Frame (17) and that the Cable is between
the Pulley and the crossbar on the Press
Frame.
Tighten the 3/8” Nylon Locknut (21)
and 3/8” x 3 3/4” Bolt (88).
Route the Short Cable (23) around the 3 1/2”
Pulley (15) attached to the lower hole in the
Front Upright (42).
Be sure that the Cable
Trap (not shown) is turned to hold the
Cable in place and that the Cable is routed
around the Pulley as shown.
Tighten the
3/8” Nylon Locknut (21) and 3/8” x 3 3/4” Bolt
(not shown).
19. Route the Short Cable (23) around the 3 1/2”
Pulley (15) attached to the upper hole in the
Press Frame (17).
Be sure that the Cable
Trap (66) is in the “3 o’clock” position and
that the Cable is routed around the Pulley
as shown.
Tighten the 3/8” Nylon Locknut
(21) and 3/8” x 3 1/2” Bolt (not shown).
Route the Short Cable (23) around the 3 1/2”
Pulley (15) attached to the upper hole in the
Front Upright (42).
Be sure that the Cable
Trap (not shown) is turned to hold the
Cable in place and that the Cable is routed
around the Pulley as shown.
Tighten the
3/8” Nylon Locknut (21) and 3/8” x 3 3/4” Bolt
(not shown).
20. Attach the end of the Short Cable (23) to the
Long “U”-Bracket (57) with a 1/4” Nylon
Locknut (2) and a 1/4” Flat Washer (10).
Do
not tighten the 1/4” Nylon Locknut. It
should be threaded onto the Cable only a
couple of turns.
17
18
CABLE ASSEMBLY
21
12
Bracket
55
58
42
21
21
23
9
88
95
7
Ball
15
Crossbar
17
15
12
3
6
9
15
15
23
21
21
66
42
17
19
57
23
2
10
20